Gantt, AL (36038): No EPA Water System
No EPA-registered water system mapped - county-level context only
Water monitoring for 36038 in Gantt, AL turns up violations in the federal record - the shortfalls are non-health-based, pointing to procedural rather than safety-critical issues.
Data source: U.S. Environmental Protection Agency (EPA) SDWIS
At a Glance
- Water No EPA violations on record for the past 5 years.
- Radon EPA Zone 3 - low predicted indoor radon (below 2 pCi/L).
What’s Happening in Gantt, Alabama
No significant water quality or safety concerns have been reported for this area. The safety score is stable.
This Summer - what to check
Season-specific maintenance for home safety. Universal tasks - apply everywhere unless noted.
-
Water Heater
Flush sediment (1–2×/year). Cuts energy use and prevents bacterial growth in low-use hot-water pockets.
Source: DOE -
Wildfire & Smoke
Clear leaves and debris from gutters and the 30-ft home-ignition zone. Replace HVAC filters with MERV 13+.
Source: Firewise -
HVAC Filter
Peak AC run. Replace filters monthly during high pollen / wildfire-smoke days; standard interval otherwise.
Source: EPA IAQ
Get notified when water quality changes in your area
Free alerts when new EPA data affects ZIP code 36038. No spam - just safety updates.
Unsubscribe anytime. We only send updates when your safety score changes. See our Privacy Policy.
How Gantt Compares
Safety Score vs. Covington County and Alabama averages
| Metric | Gantt | Covington County | Alabama |
|---|---|---|---|
| EPA Violations (total) | 0 | 15.5 | 19.1 |
County and state averages computed from 41,345 ZIP codes. Data: EPA SDWIS.
See incorrect data? Let us know
Safety & Health (4) MODERATE
Compliance Alerts for 36038
2 issues flagged based on EPA data, state regulations, and housing age estimates.
Estimates based on EPA data, U.S. Census ACS housing vintage, and state regulations. Individual homes may vary.
Service-Disruption Evidence Indicator
LowNaN/100 evidence indicator from the available infrastructure-age and EPA violation records.
This heuristic is not a calibrated probability, forecast, or property-level assessment.
Indicator based on EPA enforcement and water-violation data plus U.S. Census ACS housing vintage. It does not predict whether or when a disruption will occur.
No EPA Water System Mapped to This ZIP
ZIP code 36038 in Gantt, Alabama has no community water system directly registered with the EPA Safe Drinking Water Information System (SDWIS). This typically means residents rely on private wells, shared small systems that don't meet EPA reporting thresholds, or are served by a neighboring district that hasn't been cross-referenced to this ZIP.
The information below reflects county-level context for Gantt, Alabama - including any EPA violations, environmental hazards, or demographic factors that affect home safety in the surrounding area. It is not a water quality report for a specific utility.
If you know your water provider, search directly for its PWSID or name, or use the state SDWIS lookup to find the system serving your address.
Lead & Copper in Your Water
No Lead & Copper Rule sampling data available for systems serving this ZIP code.
Radon Risk
Radon Zone 3 - Low potential (Covington County)
Lower radon potential for this area, but testing is still recommended for individual homes. Zone 3 indicates a predicted average indoor radon screening level below 2 pCi/L. Actual levels can vary based on home construction and geology.
CO & Gas Safety
Gas Distribution Risk: Low (score: 0/100)
No gas distribution incidents recorded in this county since 2004.
The CPSC recommends CO detectors on every level of your home. Have gas appliances inspected annually by a licensed technician.
Wildfire & Smoke Risk
Smoke Risk: Low (score: 19/100)
11 wildfires recorded in this county over the past 5 years. Nearest recent wildfire: 28 km (17 miles).
Monitor air quality at AirNow.gov during fire season (June–November). A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events.
Earthquake & Seismic Risk
Risk Rating: Very Low (score: 2.0/50)
| Metric | Value |
|---|---|
| Risk Score | 2.0 |
| Risk Rating | Very Low |
| Annual Frequency | < 0.001 damaging events/yr |
| Expected Annual Loss | $19K (Very Low) |
Monitor seismic activity at the USGS Earthquake Map. Secure heavy furniture, maintain an emergency kit, and know your gas shutoff location.
Superfund Site Proximity
Proximity Risk: Very Low (score: 8/100)
Nearest NPL site: Mowbray Engineering Co. at 30.3 miles (48.8 km).
| Radius | NPL Sites |
|---|---|
| Within 5 km (3.1 mi) | 0 |
| Within 10 km (6.2 mi) | 0 |
| Within 25 km (15.5 mi) | 0 |
Nearest NPL Sites
- Mowbray Engineering Co. - 30.3 mi (Deleted), listed 09/08/1983
Search nearby sites at the EPA Superfund Site Search. If you garden or use well water near an NPL site, consider soil and water testing.
Violation Summary
Energy Costs in AL
Residential electricity rate: 17.41¢/kWh - near the national average (17.0¢/kWh).
Energy Sources
Alabama generates 6.8% of its electricity from renewable sources - 20% below the national average of 26.9%. Including nuclear, 36.8% of the state's power is carbon-free (EIA 2025).
| Source | Share |
|---|---|
| Natural gas | 45.6% |
| Nuclear | 30% |
| Coal | 15.3% |
| Hydroelectric | 5.8% |
| Solar | 0.9% |
Need help with your water quality?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
What You Can Do
- Review your annual Consumer Confidence Report (CCR) - Your utility publishes this each July
- Test your home's water - Especially if you have older plumbing (pre-1986) that may contain lead
- Stay informed - Bookmark this page to check for updates on your water quality
Need help with water testing or filtration?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
Other Water Quality Reports in Alabama
- 35004 (Moody) - 6 violations
- 35005 (Adamsville) - 3 violations
- 35006 (Adger)
- 35007 (Alabaster) - 35 violations
- 35010 (Alexander City) - 11 violations
- 35011 (Alexander City)
- 35013 (Allgood)
- 35014 (Alpine) - 2 violations
- 35015 (Alton)
- 35016 (Arab) - 6 violations
- 35019 (Baileyton) - 8 violations
- 35020 (Bessemer) - 7 violations
- 35021 (Bessemer)
- 35022 (Bessemer) - 7 violations
- 35023 (Bessemer) - 12 violations
- 35031 (Blountsville) - 5 violations
- 35032 (Bon Air)
- 35033 (Bremen)
- 35034 (Brent) - 1 violation
- 35035 (Brierfield) - 2 violations
Nearby Water Quality Reports
- 36476 (River Falls) - 5 mi
- 36421 (Andalusia) - 6 mi - 13 violations
- 36420 (Andalusia) - 8 mi - 44 violations
- 36474 (Red Level) - 8 mi - 3 violations
- 36028 (Dozier) - 10 mi
- 36467 (Opp) - 16 mi - 2 violations
- 36009 (Brantley) - 17 mi - 18 violations
- 36456 (Mc Kenzie) - 18 mi - 7 violations
- 36429 (Brooklyn) - 20 mi
- 36033 (Georgiana) - 21 mi - 10 violations
Data Sources
This report uses public data from the EPA Safe Drinking Water Information System (SDWIS). No EPA-registered water system is mapped to ZIP 36038. To look up the system serving a specific address, use the state SDWIS search tool.
Frequently Asked Questions
Is the tap water in 36038 safe to drink?
No EPA-registered public water system is mapped to ZIP 36038, so there is no federal water quality record to assess. Residents in this area are typically served by private wells or very small systems below EPA reporting thresholds. If you rely on a private well, the CDC recommends testing it at least once a year for bacteria, nitrates, and any local contaminants of concern.
Where does 36038's water come from?
There is no community water system directly registered with the EPA for ZIP 36038. Most residents in this area rely on private wells drawing from groundwater, or are served by a neighboring district that isn't cross-referenced to this ZIP in federal data. Check with your local county health department to confirm your water source.
How can I get my water tested?
Since no EPA-registered water utility is mapped to ZIP 36038, contact your local county health department or hire a certified lab for independent home water testing. The EPA recommends testing private wells at least once a year for bacteria, nitrates, and any local contaminants of concern.
Does 36038 have lead in the water?
No Lead and Copper Rule sampling data is currently available in EPA records for water systems serving ZIP code 36038. If you are concerned about lead, contact your water utility or have your tap water independently tested.
What is the radon risk in 36038?
ZIP code 36038 (Covington County) falls in EPA Radon Zone 3, indicating low radon potential. Zone 3 areas have lower radon potential, though individual homes can still have elevated radon levels depending on construction and local geology. Testing is still recommended.
USGS reports that 4 of the top compounds applied across the surrounding county are flagged by the EPA for drinking-water monitoring - see the agricultural pesticide-use section
Childhood Environmental Risk Score - 36038
Low RiskThis ZIP's score is higher than 4% of U.S. ZIP codes and 5% of those in Alabama - a relative ranking, not a verdict on any home.
Risk Factor Breakdown
Housing age is the largest contributor to this ZIP's score. Homes built before 1978 are more likely to contain lead paint, and chips and dust are a common exposure path for young children. The EPA recommends a lead-paint inspection before renovating an older home.
- Children under 6 are most vulnerable to lead exposure - there is no safe level of lead in blood
- Test your home's drinking water, especially if your home was built before 1986
What families can do
Here are calm, practical steps families in this ZIP can consider - informational guidance, not cause for alarm.
No specific actions are flagged for this ZIP. The general guidance above still applies to every family.
Know a family in 36038? A free 30-second ZIP check shows them the same lead, water, and housing data.
Lead Pipe Replacement Funding for Alabama
Key LCRI Deadlines
What This Means for You
- If your home was built before 1986, it may have lead service lines
- Your water utility is required to inventory and replace lead lines at no cost to you
- Contact your water utility to check if your address is in their inventory
Source: EPA DWSRF Lead Service Line Replacement Program, FY2025 Allotment Memorandum.
Active Alerts in Alabama
6 active weather alerts in Alabama. Severe weather can affect your water quality and home safety.
Environmental Hazards (10) HIGH
County-level hazard data for Covington
These are county-level federal records for Covington, the county that contains ZIP code 36038. They describe the whole county, not this ZIP code specifically, and are provided for regional context.
Sources: U.S. Army Corps of Engineers National Inventory of Dams, NOAA Storm Events Database, EPA air-quality design values, EPA annual Air Quality Index by county, a USGS domestic-well arsenic model, and a USGS landslide-susceptibility model. All figures are county-level and do not reflect conditions at any single address.
Termite Risk for 36038
Very Heavy Termite ZoneRequired for VA/FHA loans statewide; common in conventional transactions
VA/FHA loan will not close without clear NPMA-33 form
Termite Damage in the U.S.
- Termites cause an estimated $5 billion in property damage annually in the United States, according to the USDA.
- Standard termite treatment costs $225–$2,500; fumigation for severe infestations: $2,000–$8,000.
- Homeowner insurance typically does not cover termite damage, as it is considered preventable.
What Homeowners Should Know
- Annual termite inspections are recommended in moderate-to-heavy risk zones. Early detection can prevent thousands in repair costs.
- VA and FHA loans require a clear NPMA-33 (Wood Destroying Insect Inspection Report) for closing in most states.
- Warning signs: mud tubes on foundation walls, hollow-sounding wood, discarded wings near windows, and frass (droppings) near baseboards.
- Preventive treatment ($200–$900 per year) is far less expensive than structural damage repair, which averages $3,000 and can exceed $50,000.
- Alabama falls in a very heavy termite infestation probability (TIP) zone. Subterranean termites are the primary concern, with Formosan subterranean termites also present in this region.
Source: USDA Forest Service Termite Infestation Probability (TIP) zones, VA/FHA lender requirements, Alabama pest control regulations. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Pest Risk for 36038
High Pest Pressuretermites, mosquitoes, fire ants, cockroaches and ticks
- West Nile activity zone
- Gulf Coast tick region
Required for VA loans in all states; WDI inspection standard in most transactions
Up to $10,000 for unlicensed pesticide application
Why This Matters
- Health risks: Mosquitoes transmit West Nile virus (1,000+ U.S. cases annually). Ticks spread Lyme disease (estimated 476,000 cases/year per CDC). Rodent droppings can carry hantavirus.
- Property damage: Carpenter ants and termites cause billions in structural damage annually. Rodents gnaw wiring, creating fire hazards.
- Food safety: Cockroaches and rodents contaminate food preparation areas and can trigger allergies and asthma, especially in children.
- Alabama's climate creates year-round pest pressure. Regular professional inspections and preventive treatment are strongly recommended.
Common Questions
Source: CDC vector-borne disease surveillance, EPA pesticide regulation data, Alabama pest control board, NPMA pest prevalence maps. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Wildfire & Smoke Risk Profile
Wildfire Smoke Safety Tips
- Air purifier with HEPA filter: run in the room where you spend the most time. Close windows and doors during smoke events.
- N95 or KN95 masks: standard cloth and surgical masks do not filter fine particulate matter (PM2.5) from wildfire smoke.
- Seal gaps: use wet towels or tape around doors and windows to reduce smoke infiltration during poor air quality days.
- Monitor AQI: check AirNow.gov daily during fire season. AQI above 100 = unhealthy for sensitive groups; above 150 = unhealthy for everyone.
- Create a clean room: designate one room with the air purifier running, keep it sealed, and limit time outdoors when AQI is elevated.
Protect Your Indoor Air from Wildfire Smoke
A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events. Portable units for a single room start at $80. Whole-home solutions start at $300.
Paid Partner Product links may earn a commission - see our disclosure.
Earthquake & Seismic Risk Profile
Earthquake Preparedness Tips
- Secure heavy furniture: anchor bookshelves, water heaters, and large appliances to wall studs. Unsecured items cause most earthquake injuries.
- Emergency kit: water (1 gallon per person per day for 3 days), non-perishable food, flashlight, batteries, first aid kit, wrench to turn off gas. Keep kits at home and in your car.
- Know how to shut off gas: locate the gas meter shutoff valve and keep a wrench nearby. Gas leaks are a leading cause of post-earthquake fires.
- Drop, Cover, Hold On: during shaking, drop to hands and knees, take cover under a sturdy table, and hold on. Do not stand in doorways or run outside.
- Structural retrofit: homes built before 1980 may need foundation bolting or cripple wall bracing. FEMA's earthquake resources offer guidance on retrofitting.
- USGS ShakeMap: monitor real-time and recent seismic activity at earthquake.usgs.gov.
Build Your Earthquake Preparedness Kit
FEMA recommends every household in a seismic zone maintain a 72-hour emergency kit. Pre-assembled kits start at $40 and include water, food, first aid, and tools.
Paid Partner Product links may earn a commission - see our disclosure.
Mold Risk Assessment for 36038
Moderate RiskSummer months (June–August) present the highest mold risk in 36038, with average humidity reaching 75%. Indoor humidity can be 10–15% higher in poorly ventilated spaces. Winter humidity drops to 71%, reducing but not eliminating risk.
Why Mold Matters
- The CDC and EPA identify mold as a significant indoor health hazard. Common symptoms include respiratory irritation, allergic reactions, and asthma exacerbation.
- Mold begins growing within 24–48 hours on damp surfaces when relative humidity exceeds 60%. Bathrooms, basements, and crawl spaces are most vulnerable.
- Professional mold remediation costs $1,500–$9,000 on average. Homeowner insurance often excludes mold coverage unless caused by a "covered peril."
- Homes built before 1980 typically lack modern vapor barriers and ventilation systems, increasing moisture infiltration risk.
Prevention Recommendations
- Use a dehumidifier to keep indoor humidity below 50%. This is especially important in basements, crawl spaces, and bathrooms in high-humidity areas like 36038.
- Ensure proper ventilation: use exhaust fans in bathrooms and kitchens, and keep attic and crawl space vents unblocked.
- Fix leaks immediately. Even small plumbing leaks can create mold-favorable conditions within 48 hours.
- Monitor indoor humidity with a hygrometer ($10–$20). Target 30–50% year-round.
With 73% average humidity, a dehumidifier is the most effective way to reduce mold risk in 36038. Energy Star-rated units cost $200–$400 and can reduce humidity by 20–30%.
Respiratory Risk Snapshot
Very High RiskSuperfund Sites & Soil Contamination Risk
Nearest Superfund (NPL) Sites
| Site Name | Distance | Status | Listed |
|---|---|---|---|
|
Mowbray Engineering Co.
|
30.3 mi | Deleted from NPL | 09/08/1983 |
What Are Superfund NPL Sites?
The National Priorities List (NPL) is the EPA's list of the most contaminated sites in the United States. These sites are eligible for federal cleanup funding under CERCLA (the "Superfund" law). Common contaminants include heavy metals, volatile organic compounds (VOCs), pesticides, and industrial solvents that can leach into soil, groundwater, and air.
- Active Cleanup: EPA is investigating or remediating the site - contamination may still be present.
- Construction Complete: Physical cleanup is done, but long-term monitoring continues.
- Deleted: Site meets EPA cleanup standards and has been removed from the NPL.
Know What's in Your Soil
If you live near a Superfund site, a home soil test kit can detect heavy metals, lead, and other contaminants - especially important if you garden, have children, or use well water.
Paid Partner Product links may earn a commission - see our disclosure.
Agricultural pesticide use in the surrounding county
USGS estimates how many kilograms of agricultural pesticides are applied each year in this ZIP code’s surrounding county, plus the five most-applied compounds. These are county-level use estimates, not a measurement of any pesticide in the tap water served to this ZIP code.
Top compounds by volume
The five compounds applied in the largest amounts across this county. Where the EPA sets a drinking-water reference limit (MCL) for a compound, that limit is shown for context - it is a regulatory reference, not a finding of any concentration in this ZIP code’s water.
-
Moderate water concernGLYPHOSATEHerbicide · 15.5k kg/yr · EPA drinking-water reference limit: 700 ppb
-
Moderate water concernCHLOROTHALONILFungicide · 9.9k kg/yr
-
High water concernCHLORPYRIFOSInsecticide · 2.8k kg/yr
-
Low water concernPENDIMETHALINHerbicide · 2.2k kg/yr
-
Moderate water concern2,4-DHerbicide · 1.1k kg/yr · EPA drinking-water reference limit: 70 ppb
4 of the top compounds are ones the EPA flags for drinking-water monitoring - see the drinking-water section above
What this means
- These figures describe pesticide application across the surrounding county, not the drinking water at this address.
- An EPA Maximum Contaminant Level (MCL) is a regulatory reference for how much of a compound is allowed in finished tap water - it is not a finding of contamination at this ZIP code.
- Tested drinking-water results from the local water system - when reported - appear in the drinking-water section of this report.
Methodology: Annual county pesticide-use estimates are from the USGS Pesticide National Synthesis Project, mapped from county FIPS to ZIP code. EPA Maximum Contaminant Levels are reproduced from federal drinking-water regulations and are reference points only.
Informational only. County-level agricultural pesticide-use estimates are not a measurement of any pesticide in the drinking water served by this ZIP code, nor an assessment of health risk. Tested drinking-water results, when reported by the local water system, appear in the drinking-water section above.
Home & Infrastructure (6) OK
Housing Profile for 36038
Based on U.S. Census data (ACS B25034), there are 106 housing units in this ZIP code. The median home was built around 1984, making it roughly 42 years old.
When Homes Were Built
What This Means for Home Equipment
Homes built in the 1984s era typically have equipment that has been replaced at least once. Based on typical replacement cycles:
- Water heater: estimated ~6 years old (avg lifespan: 12 years)
- HVAC system: estimated ~8 years old (avg lifespan: 17 years)
- Plumbing: likely Copper
Home Value Context
Estimated median home value in this ZIP code based on Census ACS data. Safety remediation costs include water filtration, lead abatement, radon mitigation, and flood insurance where applicable.
Equipment Age Estimate for 36038
Based on Census data, the median home in this ZIP was built in 1984 (~42 years old). 55% of homes were built before 1986.
The EPA Lead and Copper Rule Improvements (LCRI), finalized October 2024, requires all water utilities to:
- By October 2027: Complete a lead service line inventory and notify all customers with lead or unknown lines
- By ~2037: Replace 100% of lead service lines (mandatory 10-year deadline)
- New action level: Lowered from 15 ppb to 10 ppb - more homes now trigger mandatory action
55% of homes in ZIP 36038 were built before 1986 - the year lead solder was banned. If you receive a notification letter from your water utility, your home likely has lead service lines or lead solder connections.
- Get your water tested for lead (request a test kit from your utility at no cost)
- Install a certified lead-reducing filter (NSF/ANSI 53)
- Contact your utility about replacement assistance - costs run $5,000–$15,000, utilities may cover a portion under LCRI
- Have a plumber inspect your service line connection
Likely pipe material: Copper
Estimates based on U.S. Census ACS housing vintage data and typical equipment lifespans. Actual conditions vary by home.
Infrastructure Decay & Disruption
Water pipe decay
Local water mains are modeled to reach a critical service threshold within about 5 years.
Bridge condition (FHWA NBI)
Bridge figures are from the Federal Highway Administration's National Bridge Inventory. They describe area-level structural ratings, not the safety of any specific bridge.
Bridge condition - FHWA NBI 2024 annual release
Of 332 bridges classified within this ZIP code's surrounding county, 17 are classified Poor by FHWA NBI 2024.
Good (106) · Fair (209) · Poor (17)
FHWA classifies bridges as Good (rating 7-9), Fair (5-6), or Poor (0-4) based on biennial inspections of deck, superstructure, substructure, and culvert components.
Counts are county-level aggregated; multiple ZIP codes within the same county share these counts. No per-bridge or per-structure-ID claim is made.
Source: FHWA National Bridge Inventory, 2024 annual release.
Gas pipeline incident history
PHMSA records no reported gas-distribution pipeline incidents on file for this area.
Source: U.S. Pipeline and Hazardous Materials Safety Administration (PHMSA) historical incident data.
This is a heuristic service-disruption evidence indicator, not a probability or forecast.
See the service-disruption evidence breakdown →What this means
- This score blends water-pipe decay, bridge condition, gas-pipeline incident history, and a service-disruption evidence indicator into one area-level measure of infrastructure stress.
- It describes the infrastructure around a home, not the condition of the home itself, and it is a modeled estimate rather than an engineering assessment.
- Aging water mains raise the chance of breaks and service interruptions; a plumber can inspect a home's own supply line and shut-off valve.
Methodology: Water-pipe decay is modeled with an exponential-decay bathtub curve from Census ACS housing age, EPA ECHO compliance records, and EPA infrastructure-needs data. Bridge condition is from the FHWA National Bridge Inventory; gas-pipeline incidents are from PHMSA. The service-disruption evidence indicator combines available housing-age and EPA violation records without claiming a probability or forecast. The stress score is a weighted composite of these four signals.
All figures are modeled estimates from public federal data. They are not engineering assessments, predictions of failure, or a judgment about any specific structure or utility.
Power outages in Covington
Electricity outages reported by utilities in Covington and tracked by the U.S. Department of Energy's EAGLE-I program in 2024. These figures describe the county, not conditions at ZIP code 36038.
County-level figures, not a measurement at this address. Based on reported 15-minute intervals: intervals reported with no value are excluded, never counted as zero. Counties and years without data are omitted rather than shown as zero. Source: DOE/ORNL EAGLE-I, licensed CC BY 4.0.
HVAC System Health for 36038
At 17.41¢/kWh, Alabama's electricity rates are near the national average. An efficient HVAC system can still reduce your energy bills by 20–30%.
Seasonal HVAC Tips for Alabama
- Clean AC condenser coils and clear debris
- Test AC before peak season
- Check refrigerant levels (professional tech only)
- Consider a programmable thermostat to reduce load
- Replace filter monthly in high-use months
- Keep vents unobstructed
- Schedule bi-annual professional inspection
Common HVAC Issues for 1984-Era Homes
- Undersized ductwork - older designs often can't handle modern HVAC airflow requirements
- Poor insulation - pre-1980s homes lose 25–40% more heat through walls and attic
- Obsolete refrigerant - R-22 (Freon) phased out; repair costs significantly higher
- Asbestos in duct insulation - homes before 1980 may need professional abatement before HVAC work
HVAC Questions for 36038
How do I know if my HVAC system needs replacement?
Key signs include: the system is over 15 years old, frequent repairs (more than 2 per year), uneven heating/cooling between rooms, rising energy bills despite normal use, and unusual noises or odors. Based on census data, the median home in 36038 was built in 1984, putting the estimated HVAC system age at ~8 years.
What SEER rating should I look for in a new HVAC system?
As of 2023, the federal minimum is SEER2 15 for central AC in the southern U.S. and SEER2 14 in the north. For Alabama, look for at least SEER 16–18 for good efficiency. Higher SEER ratings (20+) cost more upfront but save more in areas with high electricity rates. ENERGY STAR certified units are a reliable starting point.
How much does HVAC replacement cost in Alabama?
A full HVAC replacement (furnace + AC) typically ranges from $5,000–$12,000 depending on system size, efficiency rating, and ductwork condition. Heat pump systems range from $4,000–$10,000. Federal tax credits (25C) cover up to 30% of the cost for qualifying heat pumps and high-efficiency systems. Check our rebates page for Alabama-specific incentives.
What refrigerant does my AC use and why does it matter?
If your AC was installed before 2010, it likely uses R-22, which was banned in 2020 and now costs $50–$150/lb. Systems from 2010–2024 typically use R-410A, which is being phased down (AIM Act 2025). New systems use R-454B or R-32. When your current system needs major repair, the refrigerant type significantly affects whether repair or replacement makes more economic sense.
Should I replace my furnace before the 2028 efficiency deadline?
If the furnace in a home is over 15 years old and the area has a cold/moderate climate, planning ahead is wise. After December 2028, only 95% AFUE condensing furnaces will be available. These require PVC venting - retrofitting an older home for PVC can cost $1,500–$2,500 on top of the furnace price. Replacing before the deadline with a standard 80% AFUE unit may be more cost-effective if the venting isn't PVC-ready.
HVAC age estimate based on U.S. Census ACS housing vintage data and a 17-year replacement cycle. Actual system age varies by home.
Appliance Age Estimates for 36038
Median home built in 1984 (~42 years old). Appliance ages estimated from typical replacement cycles.
How Water Quality Affects Appliance Lifespan
Water conditions in Gantt directly impact how long your appliances last.
Homes built before 1996 have likely gone through 2+ full appliance replacement cycles. If original appliances remain, they are well past expected lifespan.
Appliance Maintenance FAQ
How often should I flush my water heater?
Flush your tank water heater at least once a year to remove sediment buildup. In areas with hard water, every 6 months is recommended. Sediment reduces heating efficiency and accelerates tank corrosion, shortening lifespan by 2–4 years.
When should I replace my dishwasher vs. repair it?
If your dishwasher is over 9 years old and the repair costs more than 50% of a new unit, replacement is generally more cost-effective. Common signs: dishes not getting clean, water pooling after cycles, or rust spots on the interior.
Does a water softener really extend appliance life?
Yes. A water softener can extend water heater lifespan by up to 30% and reduce dishwasher and washing machine maintenance by preventing mineral scale buildup on heating elements, valves, and spray arms. The Battelle Memorial Institute found that softened water kept water heaters at original factory efficiency over a 15-year period.
Estimates based on U.S. Census housing vintage data and manufacturer-average replacement cycles. Actual appliance age depends on renovation history and maintenance.
Electrical Safety for 36038
Median home built in 1984 (~42 years old).
Common Electrical Issues for 1984-Era Homes
- Aging circuit breakers - breakers can weaken over time and fail to trip during overloads, creating fire hazards
- Insufficient circuits - homes from this era may lack dedicated circuits for kitchen, bathroom, and laundry areas
- Missing GFCI/AFCI protection - current code requires GFCI in wet areas and AFCI in bedrooms; older homes often lack both
- Outdated panel capacity - 100–150 amp panels may be insufficient for modern loads (heat pumps, EV charging, home office)
⚠️ Insurance Compliance Alert
55% of homes in 36038 were built before 1986 - the era when Federal Pacific (FPE StabLok), Zinsco, and Challenger electrical panels were commonly installed.
These panels have a documented 60%+ breaker failure rate and are refused by major insurance companies including State Farm, Allstate, and Citizens (FL).
If you receive an insurance non-renewal notice or 4-point inspection failure:
- Typical deadline: 30 days to replace panel
- Replacement cost: $1,500–$4,000
- Failure to replace: insurance cancellation → mortgage default risk
Insurance blacklist: State Farm, Farmers, Allstate, USAA, Mercury, Citizens (FL), Nationwide.
When to Call an Electrician
- Burning smell from outlets or panel
- Frequent breaker trips
- Sparking or discolored outlets
- Buzzing sounds from wiring or panel
- Before buying a home (especially pre-1980)
- After any water damage or flooding
- Before adding major appliances or EV charger
- If your panel is 25+ years old
Electrical Safety Tips
- Never use a fuse with a higher amperage rating than the circuit is designed for
- Label all breakers clearly in your electrical panel
- Keep 3 feet of clearance in front of your electrical panel
- Test GFCI outlets monthly using the built-in test button
- Replace any cracked or warm outlet covers immediately
- Do not daisy-chain power strips or extension cords
Homes built before 1986 may have aluminum wiring or undersized panels. An electrical safety inspection can identify hidden fire risks.
Electrical Safety Questions for 36038
How do I know if my electrical panel needs an upgrade?
Key signs include: frequent breaker trips, a panel over 25 years old, fuses instead of circuit breakers, visible rust or corrosion, and a panel rated below 200 amps if you have modern appliances, HVAC, or an EV charger. Based on census data, the median home in 36038 was built in 1984 - homes of this age often have panels that don't meet current electrical demands.
How much does an electrical panel upgrade cost?
A panel upgrade from 100 to 200 amps typically costs $1,500–$4,000 depending on your location and the complexity of the work. If the meter base or service entrance also needs replacement, costs can reach $4,000–$6,000. Rewiring a full home (common in pre-1960 homes) ranges from $8,000–$15,000+ depending on size and accessibility.
Is aluminum wiring dangerous?
Aluminum wiring itself is not inherently dangerous, but connections between aluminum wiring and copper devices (outlets, switches) can overheat due to differential thermal expansion. The Consumer Product Safety Commission (CPSC) found that homes with aluminum wiring are 55 times more likely to have fire-hazard conditions. If your home has aluminum wiring, a qualified electrician can install COPALUM or AlumiConn connectors to make connections safe.
Is my home likely to have a Federal Pacific or Zinsco panel?
These panels were installed primarily between 1960 and 1985. Based on census data, 55% of homes in 36038 were built during this era. If your home was built in this period and the panel has never been replaced, there is a meaningful chance it contains an FPE StabLok or Zinsco panel. Look for the brand name on your breaker panel door.
Electrical risk assessment based on U.S. Census ACS housing vintage data. Actual wiring and panel condition varies by home and renovation history.
CO & Gas Safety Profile
CO & Gas Safety Tips
- Install CO detectors on every level of your home and near sleeping areas. Replace batteries annually and units every 5-7 years.
- Know gas leak signs: rotten egg smell, hissing sounds near gas lines, dead vegetation near pipelines, bubbling in standing water.
- Annual inspection: have a licensed technician inspect gas appliances (furnace, water heater, stove) every year.
- Emergency: if you smell gas, leave immediately, do not use electrical switches, and call 911 or your gas company from outside.
Protect Your Home from Carbon Monoxide
The CPSC recommends a CO detector on every level. Battery-operated models start at $20. Smart detectors with app alerts start at $35.
Paid Partner Product link may earn a commission - see our disclosure.
Remodeling Permit Requirements in Alabama
ⓘ Permits RequiredStructural, electrical, plumbing, mechanical. Cosmetic work (paint, flooring, cabinets) exempt.
Stop-work order, fines up to $500/day, required demolition of unpermitted work
Why This Matters
- Unpermitted work can reduce your home's appraised value by 10–20% and complicate or block a sale entirely.
- Homeowner insurance may deny claims for damage caused by or related to unpermitted renovations.
- Buyers' lenders may require proof of permits before approving a mortgage, especially for kitchens, bathrooms, and structural changes.
- Unpermitted electrical and plumbing work is a leading cause of house fires and water damage - permits exist to ensure safety inspections.
- If you are planning remodeling work in Alabama, contact your local building department before starting any project that alters structure, electrical, plumbing, or mechanical systems.
Remodeling Permit Questions for 36038
What remodeling work requires a permit in Alabama?
In Alabama, permits are generally required for any work that alters the structure, electrical wiring, plumbing, or mechanical systems of a home. This includes kitchen and bathroom renovations involving plumbing or electrical changes, wall removal, room additions, window enlargements, re-roofing, and HVAC replacement. Purely cosmetic work - painting, flooring, cabinet refacing without plumbing changes - typically does not require a permit. Always check with your local building department, as municipal requirements may be stricter than state minimums.
What happens if I remodel without a permit in Alabama?
Working without a required permit in Alabama can result in Stop-work order, fines up to $500/day, required demolition of unpermitted work. Beyond legal penalties, unpermitted work creates problems when selling: buyers' home inspectors and appraisers flag unpermitted additions, lenders may refuse financing, and title companies may require permits to be obtained retroactively - often at 2–3 times the original permit fee. In serious cases, you may be required to open walls for inspection or demolish non-compliant work.
How much does a remodeling permit cost in Alabama?
Remodeling permit fees in Alabama typically range from $100 to $1500, depending on the scope and value of the project. Most jurisdictions calculate fees as a percentage of the project's estimated construction cost (usually 1–2%) or use a flat fee schedule based on project type. Electrical and plumbing sub-permits may be billed separately. Contact your local building department for an exact fee quote before starting work.
Permit requirements based on Alabama building codes and ICC adoption data. Costs reflect typical municipal fee schedules and may vary by jurisdiction, project scope, and valuation. This information is for general guidance only - contact your local building department for requirements specific to your project.
Cost & Community (4) OK
True Cost of Ownership
How this ZIP compares
Where the estimate comes from
Show all 4 factors
5-year equipment outlook
No major equipment is flagged for likely replacement within five years.
What this means
- This is a modeled estimate of how much more - or less - a household here may spend each year on risk-related costs such as insurance, mitigation, testing, and maintenance, compared with a typical US ZIP.
- It is a comparison figure for context, not a bill, a quote, or financial advice.
- The 5-year equipment ranges above are separate one-time replacements, not part of the annual figure.
Methodology: Each of 13 risk verticals is assigned a dollar figure from public federal data; the total is the modeled annual difference from a median-risk US ZIP. The 5-year equipment outlook flags major home equipment whose estimated age is within five years of its typical service life; figures are national-average installed-cost ranges.
Estimates are modeled from public federal data. They are not quotes, prices, or financial or insurance advice.
Fair market rent in this ZIP
These are HUD's Fair Market Rent figures for this ZIP, the payment-standard monthly rents HUD uses for housing assistance. They are a published benchmark, not a survey of what units actually rent for today.
HUD sets the fair market rent for a 2-bedroom home in this ZIP at $790 per month.
Monthly fair market rent by home size:
HUD metro area: Covington County, AL.
Source: HUD Small Area Fair Market Rents, FY2025. A SAFMR is a HUD payment-standard figure, not a survey of actual market rents.
Tax Burden in Alabama
State tax rates affect cost of ownership. Here's how Alabama compares to national averages.
Source: Tax Foundation 2024. Income tax = top marginal rate. Sales tax = state + avg local. Property tax = effective rate on home value.
Energy Costs in Alabama
Residential electricity rate: 17.41¢/kWh - near the national average (national avg: 17.0¢/kWh · EIA, December 2025)
Alabama Energy Mix
Source: EIA Form 923, 2025 data. Renewable = solar + wind + hydro + geothermal.
Home Energy Audit for 36038
The Inflation Reduction Act provides up to $8,000 in rebates and $3,200 in annual tax credits for home energy upgrades - but many provisions phase down or expire after 2032. A professional energy audit is the first step to qualifying for these incentives. Homes in 36038 average ~42 years old, making energy audits especially impactful.
What a Home Energy Audit Covers
- Insulation levels in attic, walls, and basement
- Air leaks around windows, doors, and ducts
- Blower door test (measures total air leakage)
- HVAC efficiency and age assessment
- Water heater type and condition
- Lighting and appliance energy use
- Carbon monoxide and combustion safety
- Moisture and ventilation assessment
- Gas leak detection
- Prioritized list of recommended upgrades
- Estimated cost and savings for each upgrade
- Rebate and tax credit eligibility report
- The average home energy audit identifies $200–$400/year in savings (DOE)
- Properly sealed and insulated homes save 15% on heating and cooling costs (DOE)
- Heat pump upgrades can reduce heating costs by 30–50% compared to electric resistance
- ENERGY STAR certified windows save $101–$583/year compared to single-pane windows
- Weatherization assistance programs are available for income-qualifying households
Homes in 36038 are ~42 years old on average - older homes typically have the most to gain from an energy audit due to outdated insulation, single-pane windows, and aging HVAC systems.
Under the Inflation Reduction Act. Income limits apply for HEEHRA rebates. Tax credits require tax liability. IRS details →
To claim the $150 federal tax credit, your energy audit must meet DOE standards (10 CFR 440.21) and be performed by a qualified auditor. A DOE-compliant audit includes:
- Blower door test to measure air infiltration
- Infrared thermography to identify insulation gaps
- Combustion safety testing for gas appliances
- Written report with prioritized, cost-effective upgrade recommendations
Energy Audit Questions for 36038
How much does a home energy audit cost?
A professional home energy audit typically costs $150–$400 depending on the size of your home and the depth of testing. The Inflation Reduction Act provides a $150 tax credit for qualifying audits performed by a certified auditor, effectively covering a significant portion of the audit cost. Some utilities also subsidize audits for their customers.
What is the difference between an energy audit and a home inspection?
A home inspection (done during a home sale) evaluates structural and safety conditions. An energy audit specifically measures how your home uses energy and identifies efficiency improvements. Energy audits use specialized tools like blower doors, infrared cameras, and duct blasters that are not part of a standard home inspection. The audit produces a prioritized list of upgrades with estimated costs and savings.
How much can I save after an energy audit?
According to the U.S. Department of Energy, the average audit identifies $200–$400/year in savings. Actual savings depend on your home's age, current insulation, HVAC efficiency, and local energy rates. At current rates in Alabama, the average home spends approximately $1,828/year on electricity - a 15–25% reduction through audit-recommended upgrades could save $274–$457 annually. With homes in 36038 averaging ~42 years old, there is likely significant potential for improvement.
What rebates and tax credits are available for energy upgrades?
The Inflation Reduction Act (IRA) provides two types of incentives: (1) Tax credits up to $3,200/year for heat pumps ($2,000), insulation ($1,600), windows ($600), and the audit itself ($150); and (2) HEEHRA rebates for income-qualifying households - up to $8,000 for heat pumps, $1,600 for insulation, $2,500 for electrical panels, and $840 for heat pump dryers. Solar panels qualify for a separate 30% tax credit through 2032.
Do I need an energy audit before installing solar panels?
An energy audit is not legally required before installing solar, but the DOE strongly recommends it. Reducing your home's energy consumption before adding solar means you need a smaller (cheaper) system to cover your needs. An audit typically identifies 15–30% in energy reductions through insulation, air sealing, and HVAC improvements - which directly reduces the size and cost of a solar installation.
How long does a home energy audit take?
A comprehensive energy audit takes 2–4 hours for a typical single-family home. The auditor will inspect the attic, basement, walls, windows, HVAC system, water heater, and ductwork. Diagnostic tests (blower door, infrared scan) add precision to the findings. You will receive a written report within 1–2 weeks with prioritized recommendations and estimated costs.
Source: U.S. Energy Information Administration (EIA), U.S. Department of Energy (DOE), Inflation Reduction Act of 2022 (P.L. 117-169).
Recent Product Recalls
Recent CPSC recalls for plumbing and HVAC products that may affect homes in your area.
Madewell Double V-Neck Pullover and V-Neck Cardigan Sweaters
Topyond Pool Drain Port with Cover
XW-A17 Electric Youth All-Terrain Vehicles (ATVs)
Protect Your Home in Gantt
Based on local data for ZIP 36038, these services may benefit homeowners in your area.
Based on local data for your area. Use the tools below to explore your options.
Gutter Installation & Repair
Homes in 36038 were built around 1984 on average. Aging gutters can cause foundation damage, basement flooding, and mold - a professional assessment can prevent costly repairs.
Typical cost: Gutter installation: typically $1,000–$2,500 for a standard home
Estimate Your Home Maintenance CostsWindow Replacement
With a median build year of 1984, many homes in Gantt likely have original or outdated windows. ENERGY STAR windows can save $101–$583/year on energy bills.
Typical cost: Window replacement: typically $300–$800 per window installed
Estimate Your Home Maintenance CostsRoofing Inspection & Repair
Active weather alerts in Alabama increase the risk of roof damage from hail and high winds. A professional inspection can identify vulnerabilities.
Typical cost: Roof inspection: typically $75–$300; repairs $300–$1,500
Estimate Your Home Insurance NeedsService recommendations are based on public data for this ZIP code (FEMA, Census ACS, NWS). Actual needs vary by property. By calling, your information will be shared with an independent service provider. ZipCheckup may receive compensation. Cost estimates are approximate and vary by property, condition, and contractor.
Frequently Asked Questions
Is the tap water in 36038 safe to drink?
No EPA-registered public water system is mapped to ZIP 36038, so there is no federal water quality record to assess. Residents in this area typically rely on private wells or very small systems below EPA reporting thresholds. If you rely on a private well, the CDC recommends testing it at least once a year. ZipCheckup last updated this page in July 2026. The federal source release date is unavailable, so that month is not presented as source currency.
Where does 36038's water come from?
There is no community water system directly registered with the EPA for ZIP 36038. Most residents rely on private wells drawing from groundwater, or are served by a neighboring district that isn't cross-referenced to this ZIP in federal data. Check with your local county health department to confirm your source.
How does Gantt water compare to the national average?
Gantt's water quality ranks better than 99% of U.S. ZIP codes, and better than 99% within Alabama.
How can I get my water tested in Gantt?
Since no EPA-registered water utility is mapped to ZIP 36038, contact your local county health department or hire a certified lab for independent home water testing. The EPA recommends testing private wells at least once a year.
What is the radon risk for 36038?
36038 falls in EPA Radon Zone 3 (Low risk), located in Covington County. Zone 1 indicates the highest radon potential. Testing your home is recommended regardless of zone.
How to cite this page
ZipCheckup. (2026). Gantt, AL (36038): No EPA Water System. https://zipcheckup.com/report/36038/
@misc{zipcheckup-report-36038,
author = {{ZipCheckup}},
title = {{Gantt, AL (36038): No EPA Water System}},
year = {2026},
url = {https://zipcheckup.com/report/36038/}
}
Page version: August 2026.
Nearby ZIP Code Reports
Water quality comparison for ZIP codes near 36038
| ZIP Code | City, State | Distance | Grade | Violations |
|---|---|---|---|---|
| 36476 | River Falls, AL | 5.0 mi | N/A | 0 |
| 36421 | Andalusia, AL | 5.8 mi | N/A | 13 |
| 36420 | Andalusia, AL | 7.6 mi | N/A | 44 |
| 36474 | Red Level, AL | 7.9 mi | N/A | 3 |
| 36028 | Dozier, AL | 9.8 mi | N/A | 0 |
| 36467 | Opp, AL | 16.0 mi | N/A | 2 |
| 36009 | Brantley, AL | 16.8 mi | N/A | 18 |
| 36456 | Mc Kenzie, AL | 17.6 mi | N/A | 7 |
| 36429 | Brooklyn, AL | 19.6 mi | N/A | 0 |
| 36033 | Georgiana, AL | 21.3 mi | N/A | 10 |
Nearby ZIP Code Reports
2026 Rankings for Your Area
Overall safety breakdown
Home Safety Score →Find the right water filter
Water Filter Matcher →Compare filters, tests & services
Compare My Options →Compare with another ZIP
Compare Tool →2026 Rankings
Community resilience for this ZIP area
This is a ZIP-area measure from the CDC Social Vulnerability Index, which estimates how well a community can prepare for and recover from disasters and other hazards. A higher percentile points to a community that may need more outside support; it is not a hazard or a verdict about any single address.
The CDC ranks this ZIP area in the 24th percentile for social vulnerability nationally, in the low range.
Based on a ZIP-area population of about 144.
What drives the score (national percentile by theme):
Source: CDC/ATSDR Social Vulnerability Index 2022 (ZCTA), built from 2018-2022 American Community Survey estimates. Percentiles compare this ZIP area with all others nationally.