Oilton, OK (74052): 1 Health Violation - Grade N/A
EPA data for Oilton
The directly mapped accepted EPA record for 74052 in Oilton, OK contains 605 recorded violations for inclusive record years 2021 through 2026; 1 are marked health-based. The detailed table preserves each published federal category instead of treating every other record as a monitoring violation.
Data source: U.S. Environmental Protection Agency (EPA) SDWIS
Key Findings
4 other areas checked - no concerns found.
At a Glance
- Water EPA records show 1 health-based violation and 604 non-health on the water system serving this ZIP (5-year window).
- Lead Lead reading of 0.000 mg/L is well below EPA action level.
- Radon EPA Zone 3 - lower county-level potential, not evidence of a low home result.
What’s Happening in Oilton, Oklahoma
The available EPA record classifies 1 health-based violation as active for the water system serving this ZIP.
What's Happening
decliningHealth-based drinking-water violations increasing
Updated 2026-08-31 · Based on EPA and public utility data
Have your pipes inspected for lead solder
66% of homes in this ZIP were built before 1986, when lead solder was banned. Older plumbing may leach lead into drinking water, especially in the morning or after standing overnight.
Recommended Buyer Guides for This ZIP
Independent guides - grounded in EPA, NSF, FEMA, and CDC standards. Matched to risks detected in your area.
- Best Water Filters for Lead — Lead detection or pre-1986 plumbing
- Best Lead Paint Test Kits — Pre-1978 home risk
This Summer - what to check
Season-specific maintenance for home safety. Universal tasks - apply everywhere unless noted.
-
Water Heater
Flush sediment (1–2×/year). Cuts energy use and prevents bacterial growth in low-use hot-water pockets.
Source: DOE -
Wildfire & Smoke
Clear leaves and debris from gutters and the 30-ft home-ignition zone. Replace HVAC filters with MERV 13+.
Source: Firewise -
HVAC Filter
Peak AC run. Replace filters monthly during high pollen / wildfire-smoke days; standard interval otherwise.
Source: EPA IAQ
Get notified when water quality changes in your area
Free alerts when new EPA data affects ZIP code 74052. No spam - just safety updates.
Unsubscribe anytime. We only send updates when your safety score changes. See our Privacy Policy.
How Oilton Compares
Safety Score vs. Creek County and Oklahoma averages
| Metric | Oilton | Creek County | Oklahoma |
|---|---|---|---|
| EPA Violations (total) | 605 | 133.3 | 69.6 |
County and state averages computed from 41,345 ZIP codes. Data: EPA SDWIS.
See incorrect data? Let us know
Check the critical finding below for 74052 in Oilton - it is the only elevated condition documented in this record.
Score Breakdown
Overall Home Safety Score: Score unavailable
Required evidence is missing. Missing values remain unknown and are not imputed or renormalized.
Canonical components
Required domains
Coverage: 3 of 4 components and 2 of 3 domains observed.
Model 4.0.0; series home-safety-v4-cross-vertical.
Safety & Health (7) CRITICAL
Compliance Alerts for 74052
2 issues flagged based on EPA data, state regulations, and housing age estimates.
Estimates based on EPA data, U.S. Census ACS housing vintage, and state regulations. Individual homes may vary.
Compliance Risk Forecast
Probability of future drinking water violations based on historical patterns, enforcement trends, and system size.
95% probability of new violation within 2 years
Based on 609.45 events/year rate. Model uses Poisson distribution with trend and system-size adjustments.
Service-Disruption Evidence Indicator
Critical61/100 evidence indicator from the available infrastructure-age and EPA violation records.
This heuristic is not a calibrated probability, forecast, or property-level assessment.
Indicator based on EPA enforcement and water-violation data plus U.S. Census ACS housing vintage. It does not predict whether or when a disruption will occur.
Your Water System
ZIP code 74052 in Oilton, Oklahoma is served by Oilton (EPA ID: OK2001901). This system provides water to approximately 1,435 people from groundwater sources.
Lead & Copper in Your Water
The EPA requires water systems to monitor lead and copper levels under the Lead and Copper Rule.
| Metal | Measured Level | EPA Action Level | Status | Sample Date |
|---|---|---|---|---|
| Lead | 0 mg/L | 0.015 mg/L | Within limit | N/A |
Radon Risk
Radon Zone 3 - Lower county-level potential (Creek County)
EPA Zone 3 indicates lower county-level radon potential, not a low result for a home. Testing is needed before any threshold comparison.
CO & Gas Safety
Gas Distribution Risk: Low (score: 0/100)
No gas distribution incidents recorded in this county since 2004.
The CPSC recommends CO detectors on every level of your home. Have gas appliances inspected annually by a licensed technician.
Wildfire & Smoke Risk
Smoke Risk: Moderate (score: 44/100)
10 wildfires recorded in this county over the past 5 years. Nearest recent wildfire: 15 km (9 miles).
Monitor air quality at AirNow.gov during fire season (June–November). A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events.
Earthquake & Seismic Risk
Risk Rating: Very Low (score: 2.9/50)
| Metric | Value |
|---|---|
| Risk Score | 2.9 |
| Risk Rating | Very Low |
| Annual Frequency | < 0.001 damaging events/yr |
| Expected Annual Loss | $108K (Very Low) |
Monitor seismic activity at the USGS Earthquake Map. Secure heavy furniture, maintain an emergency kit, and know your gas shutoff location.
Superfund Site Proximity
Proximity Risk: Low (score: 21/100)
Nearest NPL site: Hudson Refinery at 11.7 miles (18.9 km).
| Radius | NPL Sites |
|---|---|
| Within 5 km (3.1 mi) | 0 |
| Within 10 km (6.2 mi) | 0 |
| Within 25 km (15.5 mi) | 1 |
Nearest NPL Sites
- Hudson Refinery - 11.7 mi (Construction Complete), listed 07/22/1999
Search nearby sites at the EPA Superfund Site Search. If you garden or use well water near an NPL site, consider soil and water testing.
Violation Summary
Recent Violations
| Date | Contaminant | Type | Status |
|---|---|---|---|
| January 1, 2026 | Revised Total Coliform Rule | Monitoring | Archived |
| January 1, 2026 | Consumer Confidence Report Rule | Monitoring | Archived |
| October 1, 2025 | Stage 1 DBP Rule | Monitoring | Addressed |
| April 1, 2025 | Contaminant 2005 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2010 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2015 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2020 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2031 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2032 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2033 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2034 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2035 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2036 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2037 | Monitoring | Resolved |
| April 1, 2025 | Atrazine | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2040 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2041 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2042 | Monitoring | Resolved |
| April 1, 2025 | Contaminant 2046 | Monitoring | Resolved |
| April 1, 2025 | Benzene | Monitoring | Resolved |
Contaminants Detected
The following contaminants have been flagged in EPA records for water systems serving this ZIP code:
| Contaminant | Category | Violations | Health-Based |
|---|---|---|---|
| Lead and Copper Rule | Treatment Technique | 17 | No |
| Contaminant 2005 | Other | 16 | No |
| Contaminant 2010 | Other | 16 | No |
| Contaminant 2015 | Other | 16 | No |
| Contaminant 2020 | Other | 16 | No |
| Contaminant 2031 | Other | 16 | No |
| Contaminant 2032 | Other | 16 | No |
| Contaminant 2033 | Other | 16 | No |
| Contaminant 2034 | Other | 16 | No |
| Contaminant 2035 | Other | 16 | No |
| Contaminant 2036 | Other | 16 | No |
| Contaminant 2037 | Other | 16 | No |
| Atrazine | Organic | 16 | No |
| Contaminant 2040 | Other | 16 | No |
| Contaminant 2041 | Other | 16 | No |
Energy Costs in OK
Residential electricity rate: 13.31¢/kWh - 22% below the national average (17.0¢/kWh).
Lower electricity rates in Oklahoma make electric appliances and heat pumps a cost-effective choice compared to other states.
Energy Sources
Oklahoma generates 44.6% of its electricity from renewable sources - 18% above the national average of 26.9%. Including nuclear, 44.6% of the state's power is carbon-free (EIA 2025).
| Source | Share |
|---|---|
| Natural gas | 44.7% |
| Wind | 41.8% |
| Coal | 10.4% |
| Hydroelectric | 1.9% |
| Solar | 0.8% |
Need help with your water quality?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
What You Can Do
- Request your water system's Consumer Confidence Report (CCR) - Your utility is required to publish this annually
- Consider a home water test - Independent testing can reveal issues in your specific plumbing
- Install a certified water filter - NSF-certified filters can address specific contaminants
- Contact your water provider - Ask about current treatment and any ongoing remediation
Need help with water testing or filtration?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
Other Water Quality Reports in Oklahoma
- 73001 (Albert)
- 73002 (Alex) - 39 violations
- 73003 (Edmond)
- 73004 (Amber) - 166 violations
- 73005 (Anadarko) - 102 violations
- 73006 (Apache) - 39 violations
- 73007 (Arcadia) - 30 violations
- 73008 (Bethany) - 7 violations
- 73009 (Binger) - 14 violations
- 73010 (Blanchard) - 677 violations
- 73011 (Bradley) - 105 violations
- 73012 (Edmond) - 8 violations
- 73013 (Edmond) - 8 violations
- 73014 (Calumet) - 90 violations
- 73015 (Carnegie) - 6 violations
- 73016 (Cashion) - 195 violations
- 73017 (Cement) - 109 violations
- 73018 (Chickasha) - 191 violations
- 73019 (Norman) - 3 violations
- 73020 (Choctaw) - 290 violations
Nearby Water Quality Reports
- 74085 (Yale) - 7 mi - 80 violations
- 74030 (Drumright) - 7 mi - 32 violations
- 74038 (Jennings) - 8 mi - 654 violations
- 74081 (Terlton) - 10 mi - 16 violations
- 74023 (Cushing) - 11 mi - 68 violations
- 74068 (Shamrock) - 11 mi
- 74034 (Hallett) - 11 mi
- 74045 (Maramec) - 13 mi - 13 violations
- 74044 (Mannford) - 13 mi - 40 violations
- 74020 (Cleveland) - 16 mi - 134 violations
Data Sources
This report uses public data from the EPA Safe Drinking Water Information System (SDWIS). View the full compliance record for Oilton (OK2001901) on EPA.gov.
Frequently Asked Questions
Is the tap water in 74052 safe to drink?
Oilton's water system has 1 health-based violation record in inclusive EPA record years 2021 through 2026. Current noncompliance includes 24 addressed and 1 unaddressed records; 491 are resolved and 89 are archived. This compliance record does not replace property-specific testing.
Where does 74052's water come from?
The primary water source for this area is groundwater. Oilton serves approximately 1,435 people.
How can I get my water tested?
Contact your local water utility for a free water quality report, or hire a certified lab for independent home water testing. The EPA recommends testing annually if you use a private well.
Does 74052 have lead in the water?
Lead and Copper Rule sampling data for ZIP code 74052 shows no detectable lead (0 mg/L), below the EPA action level of 0.015 mg/L. However, older homes with lead pipes or lead-solder plumbing may still have elevated levels at the tap.
What is the radon risk in 74052?
ZIP code 74052 (Creek County) falls in EPA Radon Zone 3, indicating low radon potential. Zone 3 areas have lower radon potential, though individual homes can still have elevated radon levels depending on construction and local geology. Testing is still recommended.
USGS reports that 3 of the top compounds applied across the surrounding county are flagged by the EPA for drinking-water monitoring - see the agricultural pesticide-use section
Environmental Incidents
Health-Based Violations
Enforcement Actions
Understanding EPA Enforcement
- MCL Violation - Contaminant exceeded the Maximum Contaminant Level set by EPA
- Treatment Technique (TT) - Water system failed to follow required treatment methods
- Formal Enforcement - EPA or state issued a legal order (administrative order, court action, or compliance order)
- Resolved - The water system returned to compliance
Source: EPA Enforcement and Compliance History Online (ECHO). Data from the Safe Drinking Water Information System (SDWIS). Updated quarterly.
Health Risks from Detected Contaminants
Polychlorinated Biphenyls (PCBs)
High RiskEPA limit: 0.0005 mg/L
Probable carcinogen; liver & thyroid damage, immune suppression
At-risk groups: pregnant women, children, people near industrial waste sites or Superfund locations
Removal: granular activated carbon (GAC), reverse osmosis · Find a filter →
Benzene
High RiskEPA limit: 0.005 mg/L
Leukemia & blood cancers (known carcinogen)
At-risk groups: people near gas stations, fuel storage, or petroleum refineries
Removal: granular activated carbon (GAC), packed-tower aeration, reverse osmosis · Find a filter →
Vinyl Chloride
High RiskEPA limit: 0.002 mg/L
Liver cancer, brain cancer (known carcinogen)
At-risk groups: long-term residents, people near industrial or Superfund sites
Removal: granular activated carbon (GAC), packed-tower aeration, reverse osmosis · Find a filter →
Total Trihalomethanes (TTHM)
High RiskEPA limit: 0.08 mg/L
Bladder & rectal cancer risk; reproductive concerns
At-risk groups: pregnant women, long-term consumers of chlorinated water, people who frequently shower in chlorinated water
Removal: granular activated carbon (GAC), carbon block filter, point-of-entry aeration · Find a filter →
Haloacetic Acids (HAA5)
High RiskEPA limit: 0.06 mg/L
Cancer risk; reproductive & developmental effects
At-risk groups: pregnant women, infants, long-term consumers of chlorinated municipal water
Removal: granular activated carbon (GAC), carbon block filter, reverse osmosis · Find a filter →
Cadmium
High RiskEPA limit: 0.005 mg/L
Kidney damage accumulating over lifetime; probable carcinogen
At-risk groups: people with low iron or calcium intake (increased absorption), people relying on older galvanized plumbing
Removal: reverse osmosis, ion exchange, coagulation/filtration · Find a filter →
Chromium-6 (Hexavalent Chromium)
High RiskEPA limit: 0.1 mg/L (total chromium; California Cr-6 MCL = 0.010 mg/L)
Stomach & intestinal cancer (known carcinogen)
At-risk groups: long-term residents, people near industrial sites, residents in areas with naturally high Cr-6 geology
Removal: reverse osmosis, strong-base anion exchange, reduction and precipitation · Find a filter →
Learn more about Chromium-6 (Hexavalent Chromium) in drinking water →
Nitrite
High RiskEPA limit: 1 mg/L (as nitrogen)
Blue baby syndrome in infants; potential carcinogen
At-risk groups: infants under 6 months, pregnant women
Removal: reverse osmosis, ion exchange (anion resin), distillation · Find a filter →
Consumer Confidence Report
Annual water quality report published by Oilton for ZIP code 74052.
What Is a Consumer Confidence Report?
Every community water system in the U.S. is required by the EPA to publish an annual Consumer Confidence Report (CCR), also known as a Water Quality Report. It lists all detected contaminants, their levels compared to federal limits (MCLs), and information about where your water comes from.
How to Read Your CCR
- MCL (Maximum Contaminant Level) - the highest level of a contaminant allowed in drinking water
- MCLG (Maximum Contaminant Level Goal) - the level below which there is no known health risk
- Action Level - used for lead and copper; triggers treatment if exceeded at the 90th percentile
- A violation means detected levels exceeded the MCL - your utility must notify you and take corrective action
Childhood Environmental Risk Score - 74052
High RiskThis ZIP's score is higher than 80% of U.S. ZIP codes and 76% of those in Oklahoma - a relative ranking, not a verdict on any home.
Risk Factor Breakdown
Water system violation history is the largest contributor to this ZIP's score. A pattern of violations can signal recurring quality issues worth monitoring, and reviewing a system's recent record helps families know what to ask about.
- Children under 6 are most vulnerable to lead exposure - there is no safe level of lead in blood
- Test your home's drinking water, especially if your home was built before 1986
- Consider a certified water filter (NSF/ANSI 53 for lead removal) for drinking and cooking water
- Ask your pediatrician about blood lead level testing at well-child visits
What families can do
Here are calm, practical steps families in this ZIP can consider - informational guidance, not cause for alarm.
- Ask your pediatrician whether a blood lead test is appropriate at a child's next well-child visit.
Know a family in 74052? A free 30-second ZIP check shows them the same lead, water, and housing data.
Lead Pipe Replacement Funding for Oklahoma
Key LCRI Deadlines
What This Means for You
- If your home was built before 1986, it may have lead service lines
- Your water utility is required to inventory and replace lead lines at no cost to you
- Contact your water utility to check if your address is in their inventory
Source: EPA DWSRF Lead Service Line Replacement Program, FY2025 Allotment Memorandum.
Active Alerts in Oklahoma
1 active weather alert in Oklahoma. Severe weather can affect your water quality and home safety.
Environmental Hazards (10) MODERATE
County-level hazard data for Creek
These are county-level federal records for Creek, the county that contains ZIP code 74052. They describe the whole county, not this ZIP code specifically, and are provided for regional context.
Sources: U.S. Army Corps of Engineers National Inventory of Dams, NOAA Storm Events Database, EPA air-quality design values, EPA annual Air Quality Index by county, a USGS domestic-well arsenic model, and a USGS landslide-susceptibility model. All figures are county-level and do not reflect conditions at any single address.
Termite Risk for 74052
Heavy Termite ZoneRequired for VA/FHA loans statewide
VA/FHA loan will not close without clear NPMA-33 form
Termite Damage in the U.S.
- Termites cause an estimated $5 billion in property damage annually in the United States, according to the USDA.
- Standard termite treatment costs $225–$2,500; fumigation for severe infestations: $2,000–$8,000.
- Homeowner insurance typically does not cover termite damage, as it is considered preventable.
What Homeowners Should Know
- Annual termite inspections are recommended in moderate-to-heavy risk zones. Early detection can prevent thousands in repair costs.
- VA and FHA loans require a clear NPMA-33 (Wood Destroying Insect Inspection Report) for closing in most states.
- Warning signs: mud tubes on foundation walls, hollow-sounding wood, discarded wings near windows, and frass (droppings) near baseboards.
- Preventive treatment ($200–$900 per year) is far less expensive than structural damage repair, which averages $3,000 and can exceed $50,000.
- Oklahoma falls in a heavy termite infestation probability (TIP) zone. Subterranean termites are the primary concern.
Source: USDA Forest Service Termite Infestation Probability (TIP) zones, VA/FHA lender requirements, Oklahoma pest control regulations. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Pest Risk for 74052
High Pest Pressuretermites, fire ants, mosquitoes, ticks and cockroaches
- West Nile activity zone
Required for VA loans in all states; not state-mandated but WDI common
Up to $5,000 per violation
Why This Matters
- Health risks: Mosquitoes transmit West Nile virus (1,000+ U.S. cases annually). Ticks spread Lyme disease (estimated 476,000 cases/year per CDC). Rodent droppings can carry hantavirus.
- Property damage: Carpenter ants and termites cause billions in structural damage annually. Rodents gnaw wiring, creating fire hazards.
- Food safety: Cockroaches and rodents contaminate food preparation areas and can trigger allergies and asthma, especially in children.
- Oklahoma's climate creates year-round pest pressure. Regular professional inspections and preventive treatment are strongly recommended.
Common Questions
Source: CDC vector-borne disease surveillance, EPA pesticide regulation data, Oklahoma pest control board, NPMA pest prevalence maps. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Wildfire & Smoke Risk Profile
Wildfire Smoke Safety Tips
- Air purifier with HEPA filter: run in the room where you spend the most time. Close windows and doors during smoke events.
- N95 or KN95 masks: standard cloth and surgical masks do not filter fine particulate matter (PM2.5) from wildfire smoke.
- Seal gaps: use wet towels or tape around doors and windows to reduce smoke infiltration during poor air quality days.
- Monitor AQI: check AirNow.gov daily during fire season. AQI above 100 = unhealthy for sensitive groups; above 150 = unhealthy for everyone.
- Create a clean room: designate one room with the air purifier running, keep it sealed, and limit time outdoors when AQI is elevated.
Protect Your Indoor Air from Wildfire Smoke
A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events. Portable units for a single room start at $80. Whole-home solutions start at $300.
Paid Partner Product links may earn a commission - see our disclosure.
Earthquake & Seismic Risk Profile
Earthquake Preparedness Tips
- Secure heavy furniture: anchor bookshelves, water heaters, and large appliances to wall studs. Unsecured items cause most earthquake injuries.
- Emergency kit: water (1 gallon per person per day for 3 days), non-perishable food, flashlight, batteries, first aid kit, wrench to turn off gas. Keep kits at home and in your car.
- Know how to shut off gas: locate the gas meter shutoff valve and keep a wrench nearby. Gas leaks are a leading cause of post-earthquake fires.
- Drop, Cover, Hold On: during shaking, drop to hands and knees, take cover under a sturdy table, and hold on. Do not stand in doorways or run outside.
- Structural retrofit: homes built before 1980 may need foundation bolting or cripple wall bracing. FEMA's earthquake resources offer guidance on retrofitting.
- USGS ShakeMap: monitor real-time and recent seismic activity at earthquake.usgs.gov.
Build Your Earthquake Preparedness Kit
FEMA recommends every household in a seismic zone maintain a 72-hour emergency kit. Pre-assembled kits start at $40 and include water, food, first aid, and tools.
Paid Partner Product links may earn a commission - see our disclosure.
Mold Risk Assessment for 74052
Moderate RiskHumidity levels in 74052 remain relatively consistent year-round (summer: 60%, winter: 64%). Mold risk does not spike seasonally, but persistent indoor moisture sources still require attention.
Why Mold Matters
- The CDC and EPA identify mold as a significant indoor health hazard. Common symptoms include respiratory irritation, allergic reactions, and asthma exacerbation.
- Mold begins growing within 24–48 hours on damp surfaces when relative humidity exceeds 60%. Bathrooms, basements, and crawl spaces are most vulnerable.
- Professional mold remediation costs $1,500–$9,000 on average. Homeowner insurance often excludes mold coverage unless caused by a "covered peril."
- Homes built before 1980 typically lack modern vapor barriers and ventilation systems, increasing moisture infiltration risk.
Prevention Recommendations
- Use a dehumidifier to keep indoor humidity below 50%. This is especially important in basements, crawl spaces, and bathrooms in high-humidity areas like 74052.
- Ensure proper ventilation: use exhaust fans in bathrooms and kitchens, and keep attic and crawl space vents unblocked.
- Fix leaks immediately. Even small plumbing leaks can create mold-favorable conditions within 48 hours.
- Homes built around 1973 often lack modern vapor barriers. Consider a professional moisture assessment to identify hidden problem areas.
- Monitor indoor humidity with a hygrometer ($10–$20). Target 30–50% year-round.
With 62% average humidity, a dehumidifier is the most effective way to reduce mold risk in 74052. Energy Star-rated units cost $200–$400 and can reduce humidity by 20–30%.
Respiratory Risk Snapshot
High RiskSuperfund Sites & Soil Contamination Risk
Nearest Superfund (NPL) Sites
| Site Name | Distance | Status | Listed |
|---|---|---|---|
|
Hudson Refinery
|
11.7 mi | Construction Complete | 07/22/1999 |
What Are Superfund NPL Sites?
The National Priorities List (NPL) is the EPA's list of the most contaminated sites in the United States. These sites are eligible for federal cleanup funding under CERCLA (the "Superfund" law). Common contaminants include heavy metals, volatile organic compounds (VOCs), pesticides, and industrial solvents that can leach into soil, groundwater, and air.
- Active Cleanup: EPA is investigating or remediating the site - contamination may still be present.
- Construction Complete: Physical cleanup is done, but long-term monitoring continues.
- Deleted: Site meets EPA cleanup standards and has been removed from the NPL.
Know What's in Your Soil
If you live near a Superfund site, a home soil test kit can detect heavy metals, lead, and other contaminants - especially important if you garden, have children, or use well water.
Paid Partner Product links may earn a commission - see our disclosure.
Agricultural pesticide use in the surrounding county
USGS estimates how many kilograms of agricultural pesticides are applied each year in this ZIP code’s surrounding county, plus the five most-applied compounds. These are county-level use estimates, not a measurement of any pesticide in the tap water served to this ZIP code.
Top compounds by volume
The five compounds applied in the largest amounts across this county. Where the EPA sets a drinking-water reference limit (MCL) for a compound, that limit is shown for context - it is a regulatory reference, not a finding of any concentration in this ZIP code’s water.
-
Moderate water concern2,4-DHerbicide · 8.4k kg/yr · EPA drinking-water reference limit: 70 ppb
-
Low water concernDICAMBAHerbicide · 886 kg/yr
-
Moderate water concernGLYPHOSATEHerbicide · 453 kg/yr · EPA drinking-water reference limit: 700 ppb
-
Low water concernPENDIMETHALINHerbicide · 313 kg/yr
-
High water concernATRAZINEHerbicide · 197 kg/yr · EPA drinking-water reference limit: 3 ppb
3 of the top compounds are ones the EPA flags for drinking-water monitoring - see the drinking-water section above
What this means
- These figures describe pesticide application across the surrounding county, not the drinking water at this address.
- An EPA Maximum Contaminant Level (MCL) is a regulatory reference for how much of a compound is allowed in finished tap water - it is not a finding of contamination at this ZIP code.
- Tested drinking-water results from the local water system - when reported - appear in the drinking-water section of this report.
Methodology: Annual county pesticide-use estimates are from the USGS Pesticide National Synthesis Project, mapped from county FIPS to ZIP code. EPA Maximum Contaminant Levels are reproduced from federal drinking-water regulations and are reference points only.
Informational only. County-level agricultural pesticide-use estimates are not a measurement of any pesticide in the drinking water served by this ZIP code, nor an assessment of health risk. Tested drinking-water results, when reported by the local water system, appear in the drinking-water section above.
Home & Infrastructure (7) MODERATE
Home Buyer Risk Report
An inspection-grade snapshot of public-data risk factors for this ZIP, built to help a buyer decide what to verify before closing.
Public federal data shows a moderate risk profile for this ZIP. Several factors below are worth verifying independently before closing.
Seven-factor inspection checklist
Each factor below is scored 0–100 from public federal data. A higher score means the factor is more worth verifying before you buy.
The local water system's recent EPA violation and contaminant history, along with an independent tap-water test, gives more context.
Homes built before 1986 may have lead pipes or solder, and pre-1978 homes may have lead paint - a lead inspection adds clarity.
Heating and cooling costs and the age of the HVAC system, along with recent utility bills, give a fuller picture.
Older homes more often have aging plumbing, wiring, and a water heater near end of life - a full inspection adds detail.
The EPA recommends testing every home for radon; homes in EPA Radon Zone 1 have the highest potential.
Nearby hazards
No EPA Superfund (National Priorities List) sites recorded within 10 km.
ATSDR published a Public Health Assessment for a nearby site (06/22/2006). Read the ATSDR assessment
Heuristic local service-disruption evidence indicator, not a probability or forecast.
See the service-disruption evidence breakdownHealthcare access
Hospitals reported by CMS Hospital Compare near this ZIP code, with overall federal quality star ratings where CMS publishes one.
Closest hospitals
-
Not rated by CMSDrumright Regional HospitalCritical access · 6.7 mi away · ER
-
CMS 4-star ratingHillcrest Hospital CushingAcute care · 10.6 mi away · ER
Across the rated hospitals within 15 miles, the average CMS overall-quality rating is 4.0 (CMS scale: 1 to 5).
Federal data from CMS Hospital Compare. Distances are straight-line estimates from the ZIP code centroid; ZipCheckup neither ranks nor recommends any hospital.
Inspection-day checklist
Practical items to raise with your inspector, agent, or the seller - tailored to this ZIP's data.
- Review the local water system's recent disruption and violation history with the utility.
- Hire an independent home inspector for a full walkthrough of the property.
- Read the seller's disclosure and any past inspection or repair records.
- Ask for service records for the HVAC system, water heater, and roof.
What this means
- This report consolidates seven home-purchase risk factors and nearby hazards from public federal data into one place.
- Each flagged item is a recommendation to verify independently - not a finding of a defect.
- An independent home inspection remains an essential step before closing.
Methodology: The report combines the home purchase risk score - a seven-factor composite of public federal data - with EPA Superfund, ATSDR, water-disruption, and NRC nuclear-zone proximity datasets. All figures are modeled estimates.
Informational only. This is a modeled summary of public federal data, not a home inspection, an appraisal, or a prediction of defects. Verify any concern with a qualified inspector before a purchase.
Housing Profile for 74052
Based on U.S. Census data (ACS B25034), there are 520 housing units in this ZIP code. The median home was built around 1973, making it roughly 53 years old.
When Homes Were Built
What This Means for Home Equipment
Homes built in the 1973s era typically have equipment that has been replaced at least once. Based on typical replacement cycles:
- Water heater: estimated ~5 years old (avg lifespan: 12 years)
- HVAC system: estimated ~2 years old (avg lifespan: 17 years)
- Plumbing: likely Copper
Home Value Context
Estimated median home value in this ZIP code based on Census ACS data. Safety remediation costs include water filtration, lead abatement, radon mitigation, and flood insurance where applicable.
Equipment Age Estimate for 74052
Based on Census data, the median home in this ZIP was built in 1973 (~53 years old). 66% of homes were built before 1986.
The EPA Lead and Copper Rule Improvements (LCRI), finalized October 2024, requires all water utilities to:
- By October 2027: Complete a lead service line inventory and notify all customers with lead or unknown lines
- By ~2037: Replace 100% of lead service lines (mandatory 10-year deadline)
- New action level: Lowered from 15 ppb to 10 ppb - more homes now trigger mandatory action
66% of homes in ZIP 74052 were built before 1986 - the year lead solder was banned. If you receive a notification letter from your water utility, your home likely has lead service lines or lead solder connections.
- Get your water tested for lead (request a test kit from your utility at no cost)
- Install a certified lead-reducing filter (NSF/ANSI 53)
- Contact your utility about replacement assistance - costs run $5,000–$15,000, utilities may cover a portion under LCRI
- Have a plumber inspect your service line connection
Likely pipe material: Copper
Estimates based on U.S. Census ACS housing vintage data and typical equipment lifespans. Actual conditions vary by home.
Infrastructure Decay & Disruption
Water pipe decay
Local water mains are modeled to reach a critical service threshold within about 1 years.
Bridge condition (FHWA NBI)
Bridge figures are from the Federal Highway Administration's National Bridge Inventory. They describe area-level structural ratings, not the safety of any specific bridge.
Bridge condition - FHWA NBI 2024 annual release
Of 395 bridges classified within this ZIP code's surrounding county, 82 are classified Poor by FHWA NBI 2024.
Good (160) · Fair (153) · Poor (82)
FHWA classifies bridges as Good (rating 7-9), Fair (5-6), or Poor (0-4) based on biennial inspections of deck, superstructure, substructure, and culvert components.
Counts are county-level aggregated; multiple ZIP codes within the same county share these counts. No per-bridge or per-structure-ID claim is made.
Source: FHWA National Bridge Inventory, 2024 annual release.
Gas pipeline incident history
PHMSA records no reported gas-distribution pipeline incidents on file for this area.
Source: U.S. Pipeline and Hazardous Materials Safety Administration (PHMSA) historical incident data.
This is a heuristic service-disruption evidence indicator, not a probability or forecast.
See the service-disruption evidence breakdown →What this means
- This score blends water-pipe decay, bridge condition, gas-pipeline incident history, and a service-disruption evidence indicator into one area-level measure of infrastructure stress.
- It describes the infrastructure around a home, not the condition of the home itself, and it is a modeled estimate rather than an engineering assessment.
- Aging water mains raise the chance of breaks and service interruptions; a plumber can inspect a home's own supply line and shut-off valve.
Concerned about aging water lines on your property? - talk to a local expert.
Call (855) 384-4856Paid Partner This is a free service. You will be connected with an independent service provider. We may receive compensation.
Methodology: Water-pipe decay is modeled with an exponential-decay bathtub curve from Census ACS housing age, EPA ECHO compliance records, and EPA infrastructure-needs data. Bridge condition is from the FHWA National Bridge Inventory; gas-pipeline incidents are from PHMSA. The service-disruption evidence indicator combines available housing-age and EPA violation records without claiming a probability or forecast. The stress score is a weighted composite of these four signals.
All figures are modeled estimates from public federal data. They are not engineering assessments, predictions of failure, or a judgment about any specific structure or utility.
Power outages in Creek
Electricity outages reported by utilities in Creek and tracked by the U.S. Department of Energy's EAGLE-I program in 2024. These figures describe the county, not conditions at ZIP code 74052.
County-level figures, not a measurement at this address. Based on reported 15-minute intervals: intervals reported with no value are excluded, never counted as zero. Counties and years without data are omitted rather than shown as zero. Source: DOE/ORNL EAGLE-I, licensed CC BY 4.0.
HVAC System Health for 74052
Lower electricity rates in Oklahoma (13.31¢/kWh) help offset HVAC costs, but an aging system still wastes energy. Modern high-efficiency systems can reduce consumption by 20–40%.
Seasonal HVAC Tips for Oklahoma
- Schedule furnace tune-up before first cold snap
- Replace air filter (every 1–3 months)
- Check thermostat calibration
- Clean AC condenser coils and clear debris
- Test AC before peak season
- Check refrigerant levels (professional tech only)
Common HVAC Issues for 1973-Era Homes
- Undersized ductwork - older designs often can't handle modern HVAC airflow requirements
- Poor insulation - pre-1980s homes lose 25–40% more heat through walls and attic
- Obsolete refrigerant - R-22 (Freon) phased out; repair costs significantly higher
- Asbestos in duct insulation - homes before 1980 may need professional abatement before HVAC work
The Department of Energy requires all NEW furnaces manufactured after December 18, 2028 to meet 95% AFUE (condensing furnaces). Current standard is 80% AFUE.
What this means for you:
- 80% AFUE non-condensing furnaces will no longer be available for purchase
- Condensing furnaces require PVC venting (additional $1,500–$2,500 for retrofit)
- If the furnace is approaching end of life, consider replacing before the deadline to potentially save on installation costs
- Your existing furnace can continue operating - this applies only to NEW equipment
HVAC Questions for 74052
How do I know if my HVAC system needs replacement?
Key signs include: the system is over 15 years old, frequent repairs (more than 2 per year), uneven heating/cooling between rooms, rising energy bills despite normal use, and unusual noises or odors. Based on census data, the median home in 74052 was built in 1973, putting the estimated HVAC system age at ~2 years.
What SEER rating should I look for in a new HVAC system?
As of 2023, the federal minimum is SEER2 15 for central AC in the southern U.S. and SEER2 14 in the north. For Oklahoma, look for at least SEER 16–18 for good efficiency. Higher SEER ratings (20+) cost more upfront but save more in areas with high electricity rates. ENERGY STAR certified units are a reliable starting point.
How much does HVAC replacement cost in Oklahoma?
A full HVAC replacement (furnace + AC) typically ranges from $5,000–$12,000 depending on system size, efficiency rating, and ductwork condition. Heat pump systems range from $4,000–$10,000. Federal tax credits (25C) cover up to 30% of the cost for qualifying heat pumps and high-efficiency systems. Check our rebates page for Oklahoma-specific incentives.
What refrigerant does my AC use and why does it matter?
If your AC was installed before 2010, it likely uses R-22, which was banned in 2020 and now costs $50–$150/lb. Systems from 2010–2024 typically use R-410A, which is being phased down (AIM Act 2025). New systems use R-454B or R-32. When your current system needs major repair, the refrigerant type significantly affects whether repair or replacement makes more economic sense.
Should I replace my furnace before the 2028 efficiency deadline?
If the furnace in a home is over 15 years old and the area has a cold/moderate climate, planning ahead is wise. After December 2028, only 95% AFUE condensing furnaces will be available. These require PVC venting - retrofitting an older home for PVC can cost $1,500–$2,500 on top of the furnace price. Replacing before the deadline with a standard 80% AFUE unit may be more cost-effective if the venting isn't PVC-ready.
HVAC age estimate based on U.S. Census ACS housing vintage data and a 17-year replacement cycle. Actual system age varies by home.
Appliance Age Estimates for 74052
Median home built in 1973 (~53 years old). Appliance ages estimated from typical replacement cycles.
1 appliance likely is near or past typical replacement age.
How Water Quality Affects Appliance Lifespan
Water conditions in Oilton directly impact how long your appliances last.
Homes built before 1996 have likely gone through 2+ full appliance replacement cycles. If original appliances remain, they are well past expected lifespan.
Appliance Maintenance FAQ
How often should I flush my water heater?
Flush your tank water heater at least once a year to remove sediment buildup. In areas with hard water, every 6 months is recommended. Sediment reduces heating efficiency and accelerates tank corrosion, shortening lifespan by 2–4 years.
When should I replace my dishwasher vs. repair it?
If your dishwasher is over 9 years old and the repair costs more than 50% of a new unit, replacement is generally more cost-effective. Common signs: dishes not getting clean, water pooling after cycles, or rust spots on the interior.
Does a water softener really extend appliance life?
Yes. A water softener can extend water heater lifespan by up to 30% and reduce dishwasher and washing machine maintenance by preventing mineral scale buildup on heating elements, valves, and spray arms. The Battelle Memorial Institute found that softened water kept water heaters at original factory efficiency over a 15-year period.
Estimates based on U.S. Census housing vintage data and manufacturer-average replacement cycles. Actual appliance age depends on renovation history and maintenance.
Electrical Safety for 74052
Median home built in 1973 (~53 years old). 28% of homes were built before 1970, when electrical standards were significantly different.
Common Electrical Issues for 1973-Era Homes
- Knob-and-tube wiring - common in pre-1950 homes, lacks grounding and cannot safely handle modern electrical loads
- Undersized electrical panel - 60–100 amp panels typical of this era cannot support today's appliances, EV chargers, or HVAC systems
- Aluminum wiring - used in 1960s–1970s homes, poses fire risk at connections due to oxidation and thermal expansion
- Ungrounded outlets - two-prong outlets indicate missing ground wire, increasing shock and surge risk
- Federal Pacific / Zinsco panels - common in 1960s–1980s homes, known for breaker failure; replacement strongly recommended
⚠️ Insurance Compliance Alert
66% of homes in 74052 were built before 1986 - the era when Federal Pacific (FPE StabLok), Zinsco, and Challenger electrical panels were commonly installed.
These panels have a documented 60%+ breaker failure rate and are refused by major insurance companies including State Farm, Allstate, and Citizens (FL).
If you receive an insurance non-renewal notice or 4-point inspection failure:
- Typical deadline: 30 days to replace panel
- Replacement cost: $1,500–$4,000
- Failure to replace: insurance cancellation → mortgage default risk
Insurance blacklist: State Farm, Farmers, Allstate, USAA, Mercury, Citizens (FL), Nationwide.
When to Call an Electrician
- Burning smell from outlets or panel
- Frequent breaker trips
- Sparking or discolored outlets
- Buzzing sounds from wiring or panel
- Before buying a home (especially pre-1980)
- After any water damage or flooding
- Before adding major appliances or EV charger
- If your panel is 25+ years old
Electrical Safety Tips
- Never use a fuse with a higher amperage rating than the circuit is designed for
- Label all breakers clearly in your electrical panel
- Keep 3 feet of clearance in front of your electrical panel
- Test GFCI outlets monthly using the built-in test button
- Replace any cracked or warm outlet covers immediately
- Do not daisy-chain power strips or extension cords
Homes built before 1976 likely have outdated wiring and panels that do not meet current electrical codes. A professional electrical inspection is strongly recommended.
Electrical Safety Questions for 74052
How do I know if my electrical panel needs an upgrade?
Key signs include: frequent breaker trips, a panel over 25 years old, fuses instead of circuit breakers, visible rust or corrosion, and a panel rated below 200 amps if you have modern appliances, HVAC, or an EV charger. Based on census data, the median home in 74052 was built in 1973 - homes of this age often have panels that don't meet current electrical demands.
How much does an electrical panel upgrade cost?
A panel upgrade from 100 to 200 amps typically costs $1,500–$4,000 depending on your location and the complexity of the work. If the meter base or service entrance also needs replacement, costs can reach $4,000–$6,000. Rewiring a full home (common in pre-1960 homes) ranges from $8,000–$15,000+ depending on size and accessibility.
Is aluminum wiring dangerous?
Aluminum wiring itself is not inherently dangerous, but connections between aluminum wiring and copper devices (outlets, switches) can overheat due to differential thermal expansion. The Consumer Product Safety Commission (CPSC) found that homes with aluminum wiring are 55 times more likely to have fire-hazard conditions. If your home has aluminum wiring, a qualified electrician can install COPALUM or AlumiConn connectors to make connections safe.
Is my home likely to have a Federal Pacific or Zinsco panel?
These panels were installed primarily between 1960 and 1985. Based on census data, 66% of homes in 74052 were built during this era. If your home was built in this period and the panel has never been replaced, there is a meaningful chance it contains an FPE StabLok or Zinsco panel. Look for the brand name on your breaker panel door.
Electrical risk assessment based on U.S. Census ACS housing vintage data. Actual wiring and panel condition varies by home and renovation history.
CO & Gas Safety Profile
CO & Gas Safety Tips
- Install CO detectors on every level of your home and near sleeping areas. Replace batteries annually and units every 5-7 years.
- Know gas leak signs: rotten egg smell, hissing sounds near gas lines, dead vegetation near pipelines, bubbling in standing water.
- Annual inspection: have a licensed technician inspect gas appliances (furnace, water heater, stove) every year.
- Emergency: if you smell gas, leave immediately, do not use electrical switches, and call 911 or your gas company from outside.
Protect Your Home from Carbon Monoxide
The CPSC recommends a CO detector on every level. Battery-operated models start at $20. Smart detectors with app alerts start at $35.
Paid Partner Product link may earn a commission - see our disclosure.
Remodeling Permit Requirements in Oklahoma
✓ Limited EnforcementElectrical and plumbing statewide. Structural permits in municipalities adopting building codes.
Fines up to $500/day where codes adopted
Why This Matters
- Unpermitted work can reduce your home's appraised value by 10–20% and complicate or block a sale entirely.
- Homeowner insurance may deny claims for damage caused by or related to unpermitted renovations.
- Buyers' lenders may require proof of permits before approving a mortgage, especially for kitchens, bathrooms, and structural changes.
- Unpermitted electrical and plumbing work is a leading cause of house fires and water damage - permits exist to ensure safety inspections.
- If you are planning remodeling work in Oklahoma, contact your local building department before starting any project that alters structure, electrical, plumbing, or mechanical systems.
Remodeling Permit Questions for 74052
What remodeling work requires a permit in Oklahoma?
In Oklahoma, permits are generally required for any work that alters the structure, electrical wiring, plumbing, or mechanical systems of a home. This includes kitchen and bathroom renovations involving plumbing or electrical changes, wall removal, room additions, window enlargements, re-roofing, and HVAC replacement. Purely cosmetic work - painting, flooring, cabinet refacing without plumbing changes - typically does not require a permit. Always check with your local building department, as municipal requirements may be stricter than state minimums.
What happens if I remodel without a permit in Oklahoma?
Working without a required permit in Oklahoma can result in Fines up to $500/day where codes adopted. Beyond legal penalties, unpermitted work creates problems when selling: buyers' home inspectors and appraisers flag unpermitted additions, lenders may refuse financing, and title companies may require permits to be obtained retroactively - often at 2–3 times the original permit fee. In serious cases, you may be required to open walls for inspection or demolish non-compliant work.
How much does a remodeling permit cost in Oklahoma?
Remodeling permit fees in Oklahoma typically range from $50 to $1200, depending on the scope and value of the project. Most jurisdictions calculate fees as a percentage of the project's estimated construction cost (usually 1–2%) or use a flat fee schedule based on project type. Electrical and plumbing sub-permits may be billed separately. Contact your local building department for an exact fee quote before starting work.
Permit requirements based on Oklahoma building codes and ICC adoption data. Costs reflect typical municipal fee schedules and may vary by jurisdiction, project scope, and valuation. This information is for general guidance only - contact your local building department for requirements specific to your project.
Home maintenance concerns detected - talk to a local expert.
Call (855) 384-4856Paid Partner This is a free service. You will be connected with an independent service provider. We may receive compensation.
Cost & Community (8) HIGH
True Cost of Ownership
How this ZIP compares
Where the estimate comes from
Show all 4 factors
5-year equipment outlook
No major equipment is flagged for likely replacement within five years.
What this means
- This is a modeled estimate of how much more - or less - a household here may spend each year on risk-related costs such as insurance, mitigation, testing, and maintenance, compared with a typical US ZIP.
- It is a comparison figure for context, not a bill, a quote, or financial advice.
- The 5-year equipment ranges above are separate one-time replacements, not part of the annual figure.
Methodology: Each of 13 risk verticals is assigned a dollar figure from public federal data; the total is the modeled annual difference from a median-risk US ZIP. The 5-year equipment outlook flags major home equipment whose estimated age is within five years of its typical service life; figures are national-average installed-cost ranges.
Estimates are modeled from public federal data. They are not quotes, prices, or financial or insurance advice.
Affordability-Adjusted Risk Score
What This Means
Based on current ACS data for Oilton (74052), household income falls well short of what a full remediation of documented safety issues would cost for many residents - the high affordability-risk classification reflects this gap directly, and sequencing repairs while checking federal or state assistance eligibility is the most practical path forward.
- Lower-income communities face disproportionate exposure to environmental hazards
- Federal and state programs may help offset costs - check eligibility below
- This score combines water quality, housing age, and income data from EPA and Census sources
Environmental Justice Context: The EPA recognizes that low-income and minority communities often bear a disproportionate burden of environmental hazards. Use the EPA EJScreen tool to explore environmental justice indicators for your area.
Sources: Census ACS 5-Year B19013 (income), EPA SDWIS (water quality), Census ACS B25034 (housing age). Remediation costs are estimates based on typical residential systems.
Fair market rent in this ZIP
These are HUD's Fair Market Rent figures for this ZIP, the payment-standard monthly rents HUD uses for housing assistance. They are a published benchmark, not a survey of what units actually rent for today.
HUD sets the fair market rent for a 2-bedroom home in this ZIP at $1,020 per month.
Monthly fair market rent by home size:
HUD metro area: Tulsa, OK HUD Metro FMR Area.
Source: HUD Small Area Fair Market Rents, FY2025. A SAFMR is a HUD payment-standard figure, not a survey of actual market rents.
Subsidized rental housing in this ZIP
These counts come from HUD's Picture of Subsidized Households, which tracks federally subsidized rental units across all HUD programs. They describe housing assistance reported in this ZIP, not a judgment about the area.
HUD reports 22 federally subsidized rental units in this ZIP.
What HUD reports here:
Source: HUD Picture of Subsidized Households, 2025. HUD suppresses small counts; a suppressed value is treated as not reported, not zero.
Tax Burden in Oklahoma
State tax rates affect cost of ownership. Here's how Oklahoma compares to national averages.
Source: Tax Foundation 2024. Income tax = top marginal rate. Sales tax = state + avg local. Property tax = effective rate on home value.
Energy Costs in Oklahoma
Residential electricity rate: 13.31¢/kWh - 22% below the national average (national avg: 17.0¢/kWh · EIA, December 2025)
Oklahoma Energy Mix
Source: EIA Form 923, 2025 data. Renewable = solar + wind + hydro + geothermal.
Electric Utility for 74052
Source: U.S. Energy Information Administration, Form EIA-861 (2024 data). EIA ID: 14063.
Home Energy Audit for 74052
The Inflation Reduction Act provides up to $8,000 in rebates and $3,200 in annual tax credits for home energy upgrades - but many provisions phase down or expire after 2032. A professional energy audit is the first step to qualifying for these incentives. Homes in 74052 average ~53 years old, making energy audits especially impactful.
What a Home Energy Audit Covers
- Insulation levels in attic, walls, and basement
- Air leaks around windows, doors, and ducts
- Blower door test (measures total air leakage)
- HVAC efficiency and age assessment
- Water heater type and condition
- Lighting and appliance energy use
- Carbon monoxide and combustion safety
- Moisture and ventilation assessment
- Gas leak detection
- Prioritized list of recommended upgrades
- Estimated cost and savings for each upgrade
- Rebate and tax credit eligibility report
- The average home energy audit identifies $200–$400/year in savings (DOE)
- Properly sealed and insulated homes save 15% on heating and cooling costs (DOE)
- Heat pump upgrades can reduce heating costs by 30–50% compared to electric resistance
- ENERGY STAR certified windows save $101–$583/year compared to single-pane windows
- Weatherization assistance programs are available for income-qualifying households
Homes in 74052 are ~53 years old on average - older homes typically have the most to gain from an energy audit due to outdated insulation, single-pane windows, and aging HVAC systems.
Oklahoma Gas & Electric Co (Investor-owned) serves 74052. Your local residential rate is 11.8¢/kWh , which is below the national average - but efficiency upgrades still pay for themselves over time . Many utilities offer additional rebates on top of federal IRA incentives - ask your energy auditor about programs from Oklahoma Gas & Electric Co.
Under the Inflation Reduction Act. Income limits apply for HEEHRA rebates. Tax credits require tax liability. IRS details →
To claim the $150 federal tax credit, your energy audit must meet DOE standards (10 CFR 440.21) and be performed by a qualified auditor. A DOE-compliant audit includes:
- Blower door test to measure air infiltration
- Infrared thermography to identify insulation gaps
- Combustion safety testing for gas appliances
- Written report with prioritized, cost-effective upgrade recommendations
Energy Audit Questions for 74052
How much does a home energy audit cost?
A professional home energy audit typically costs $150–$400 depending on the size of your home and the depth of testing. The Inflation Reduction Act provides a $150 tax credit for qualifying audits performed by a certified auditor, effectively covering a significant portion of the audit cost. Some utilities also subsidize audits for their customers - check with Oklahoma Gas & Electric Co for local programs.
What is the difference between an energy audit and a home inspection?
A home inspection (done during a home sale) evaluates structural and safety conditions. An energy audit specifically measures how your home uses energy and identifies efficiency improvements. Energy audits use specialized tools like blower doors, infrared cameras, and duct blasters that are not part of a standard home inspection. The audit produces a prioritized list of upgrades with estimated costs and savings.
How much can I save after an energy audit?
According to the U.S. Department of Energy, the average audit identifies $200–$400/year in savings. Actual savings depend on your home's age, current insulation, HVAC efficiency, and local energy rates. At current rates in Oklahoma, the average home spends approximately $1,398/year on electricity - a 15–25% reduction through audit-recommended upgrades could save $210–$350 annually. With homes in 74052 averaging ~53 years old, there is likely significant potential for improvement.
What rebates and tax credits are available for energy upgrades?
The Inflation Reduction Act (IRA) provides two types of incentives: (1) Tax credits up to $3,200/year for heat pumps ($2,000), insulation ($1,600), windows ($600), and the audit itself ($150); and (2) HEEHRA rebates for income-qualifying households - up to $8,000 for heat pumps, $1,600 for insulation, $2,500 for electrical panels, and $840 for heat pump dryers. Solar panels qualify for a separate 30% tax credit through 2032.
Do I need an energy audit before installing solar panels?
An energy audit is not legally required before installing solar, but the DOE strongly recommends it. Reducing your home's energy consumption before adding solar means you need a smaller (cheaper) system to cover your needs. An audit typically identifies 15–30% in energy reductions through insulation, air sealing, and HVAC improvements - which directly reduces the size and cost of a solar installation.
How long does a home energy audit take?
A comprehensive energy audit takes 2–4 hours for a typical single-family home. The auditor will inspect the attic, basement, walls, windows, HVAC system, water heater, and ductwork. Diagnostic tests (blower door, infrared scan) add precision to the findings. You will receive a written report within 1–2 weeks with prioritized recommendations and estimated costs.
Source: U.S. Energy Information Administration (EIA), U.S. Department of Energy (DOE), Inflation Reduction Act of 2022 (P.L. 117-169).
Safety Updates for Oilton, Oklahoma
Violations & Enforcement Timeline
View all 11 records
Related Anomalies
Recent Product Recalls
Recent CPSC recalls for plumbing and HVAC products that may affect homes in your area.
Madewell Double V-Neck Pullover and V-Neck Cardigan Sweaters
Topyond Pool Drain Port with Cover
XW-A17 Electric Youth All-Terrain Vehicles (ATVs)
Protect Your Home in Oilton
Based on local data for ZIP 74052, these services may benefit homeowners in your area.
Based on local data for your area. Use the tools below to explore your options.
Gutter Installation & Repair
Homes in 74052 were built around 1973 on average. Aging gutters can cause foundation damage, basement flooding, and mold - a professional assessment can prevent costly repairs.
Typical cost: Gutter installation: typically $1,000–$2,500 for a standard home
Estimate Your Home Maintenance CostsWindow Replacement
With a median build year of 1973, many homes in Oilton likely have original or outdated windows. ENERGY STAR windows can save $101–$583/year on energy bills.
Typical cost: Window replacement: typically $300–$800 per window installed
Estimate Your Home Maintenance CostsRoofing Inspection & Repair
Homes built around 1973 may be on their second or third roof. A professional inspection can catch damage before leaks start.
Typical cost: Roof inspection: typically $75–$300; repairs $300–$1,500
Estimate Your Home Insurance NeedsService recommendations are based on public data for this ZIP code (FEMA, Census ACS, NWS). Actual needs vary by property. By calling, your information will be shared with an independent service provider. ZipCheckup may receive compensation. Cost estimates are approximate and vary by property, condition, and contractor.
SNAP food retailers in this ZIP
These are stores located in this ZIP that are currently authorized to accept SNAP (food stamp) benefits. The count reflects where stores are located, not how easy groceries are to reach; a resident may shop in a nearby ZIP.
3 SNAP-authorized food retailers are located in this ZIP.
Store types located here:
Source: USDA FNS Historical SNAP Retailer Locator (active authorizations), December 2025. A store is counted where it is located; this is not a measure of grocery access.
Take Action
Concerned about these findings? Contact your local elected officials to ask what is being done about water quality in your area.
Email Your RepresentativeDon't know who to contact? Find your local representative at usa.gov/elected-officials
Frequently Asked Questions
Is the tap water in 74052 safe to drink?
Based on EPA SDWIS data, Oilton's primary water system (Oilton) has 605 recorded violations in the past 5 years, including 1 health-based. Check the full report above for details. ZipCheckup last updated this page in July 2026. The federal source release date is unavailable, so that month is not presented as source currency.
Where does 74052's water come from?
The primary water source for ZIP code 74052 is Groundwater. Oilton serves approximately 1,435 people.
How does Oilton water compare to the national average?
Oilton's water quality ranks better than 64% of U.S. ZIP codes, and in the bottom 58% within Oklahoma.
How can I get my water tested in Oilton?
Contact your local water utility (Oilton) for a free Consumer Confidence Report, or hire a certified lab for independent home water testing. The EPA recommends annual testing if you use a private well.
What is the radon risk for 74052?
74052 falls in EPA Radon Zone 3 (Low risk), located in Creek County. Zone 1 indicates the highest radon potential. Testing your home is recommended regardless of zone.
How to cite this page
ZipCheckup. (2026). Oilton, OK (74052): 1 Health Violation - Grade N/A. https://zipcheckup.com/report/74052/
@misc{zipcheckup-report-74052,
author = {{ZipCheckup}},
title = {{Oilton, OK (74052): 1 Health Violation - Grade N/A}},
year = {2026},
url = {https://zipcheckup.com/report/74052/}
}
Page version: August 2026.
Nearby ZIP Code Reports
Water quality comparison for ZIP codes near 74052
| ZIP Code | City, State | Distance | Grade | Violations |
|---|---|---|---|---|
| 74085 | Yale, OK | 6.6 mi | N/A | 80 |
| 74030 | Drumright, OK | 6.7 mi | A | 32 |
| 74038 | Jennings, OK | 8.2 mi | N/A | 654 |
| 74081 | Terlton, OK | 10.3 mi | N/A | 16 |
| 74023 | Cushing, OK | 10.6 mi | N/A | 68 |
| 74068 | Shamrock, OK | 10.8 mi | N/A | 0 |
| 74034 | Hallett, OK | 11.4 mi | N/A | 0 |
| 74045 | Maramec, OK | 12.9 mi | N/A | 13 |
| 74044 | Mannford, OK | 13.4 mi | A | 40 |
| 74020 | Cleveland, OK | 16.1 mi | N/A | 134 |
Nearby ZIP Code Reports
2026 Rankings for Your Area
Overall safety breakdown
Home Safety Score →Find the right water filter
Water Filter Matcher →Compare filters, tests & services
Compare My Options →Compare with another ZIP
Compare Tool →2026 Rankings
Community resilience for this ZIP area
This is a ZIP-area measure from the CDC Social Vulnerability Index, which estimates how well a community can prepare for and recover from disasters and other hazards. A higher percentile points to a community that may need more outside support; it is not a hazard or a verdict about any single address.
The CDC ranks this ZIP area in the 55th percentile for social vulnerability nationally, in the elevated range.
Based on a ZIP-area population of about 959.
What drives the score (national percentile by theme):
Source: CDC/ATSDR Social Vulnerability Index 2022 (ZCTA), built from 2018-2022 American Community Survey estimates. Percentiles compare this ZIP area with all others nationally.