Tannersville, PA (18372): Lead Above EPA Limit — 33/100
EPA data for Brodhead Creek Reg Water Authority
Federal compliance data for 18372 in Tannersville, PA documents 4 violations at the health-based level — a category distinct from procedural shortfalls, where contaminant concentrations actually surpassed the applicable EPA MCL and required the system to formally notify customers and demonstrate corrective action.
Data source: U.S. Environmental Protection Agency (EPA) SDWIS Last verified: April 2, 2026
Key Findings
5 other areas checked — no concerns found.
At a Glance
- Water EPA records show 4 health-based violations and 25 non-health on the water system serving this ZIP (5-year window).
- Lead 90th-percentile lead reading of 0.123 mg/L exceeds the EPA action level (0.015 mg/L).
- Radon EPA Zone 1 — predicted average indoor radon above 4 pCi/L. Test your home.
- Flood 17 cumulative NFIP flood claims — limited flood history.
What’s Happening in Tannersville, Pennsylvania
Lead levels exceed the EPA action level of 15 ppb. 4 active health-based violations are currently on record for the water system serving this ZIP. This area is in EPA Radon Zone 1 (highest risk).
What's Happening
improvingScore improving — violations decreasing
Updated 2026-06-03 · Based on EPA and public utility data
Get your water tested for lead immediately
The most recent lead sample for this ZIP recorded 0.1228 mg/L — above the EPA action level of 0.015 mg/L. Lead exposure is particularly dangerous for children and pregnant women.
Recommended Buyer Guides for This ZIP
Independent guides — grounded in EPA, NSF, FEMA, and CDC standards. Matched to risks detected in your area.
- Best Water Filters for Lead — Lead detection or pre-1986 plumbing
- Best Under-Sink Reverse Osmosis Systems — Multi-contaminant removal
- Best Radon Test Kits — EPA Radon Zone 1 (highest risk)
This Summer — what to check
Season-specific maintenance for home safety. Universal tasks — apply everywhere unless noted.
-
Water Heater
Flush sediment (1–2×/year). Cuts energy use and prevents bacterial growth in low-use hot-water pockets.
Source: DOE -
Wildfire & Smoke
Clear leaves and debris from gutters and the 30-ft home-ignition zone. Replace HVAC filters with MERV 13+.
Source: Firewise -
HVAC Filter
Peak AC run. Replace filters monthly during high pollen / wildfire-smoke days; standard interval otherwise.
Source: EPA IAQ
Get notified when water quality changes in your area
Free alerts when new EPA data affects ZIP code 18372. No spam — just safety updates.
Unsubscribe anytime. We only send updates when your safety score changes. See our Privacy Policy.
How Tannersville Compares
Safety Score vs. Monroe County and Pennsylvania averages
| Metric | Tannersville | Monroe County | Pennsylvania |
|---|---|---|---|
| Safety Score | 33 | 48 | 55 |
| EPA Violations (total) | 29 | 5.3 | 5.8 |
| Lead (ppb) | 122.8 | 31.5 | 13.7 |
County and state averages computed from 41,344 ZIP codes. Data: EPA SDWIS.
Each number below connects you directly to a licensed specialist contractor in your area. Calls are free.
Lead level: 1,000.0 ppb — exceeds EPA action level (15 ppb)
58% of homes built before 1986 (lead solder era)
4 health-based water quality violations on record
29 total EPA violations recorded for Brodhead Creek Reg Water Authority
Recent EPA enforcement actions against this water system
EPA Lead and Copper Rule Revision (LCRR) requires utilities to inventory and begin replacing lead service lines
58% of homes built before 1986 (lead solder ban year)
Latest lead sampling: 122.8 ppb
Lead pipe risk assessment: elevated
State LCRI funding: $135M allocated for lead pipe replacement
See incorrect data? Let us know
Federal compliance filings, environmental monitoring outputs, and risk-model results for 18372 in Tannersville together turn up 2 critical-level findings and 0 high-priority findings — each card below names the specific issue, its data source, and what it means for residents.
🔍Key Insights for Tannersville 18372
Derived from EPA, Census, FEMA, and EIA data — exclusive to ZipCheckup
Score Breakdown
How your Home Safety Score of 24 is calculated.
Score improved by 3 points over 90 days.
Safety & Health (8) HIGH
Compliance Alerts for 18372
4 issues flagged based on EPA data, state regulations, and housing age estimates.
Estimates based on EPA data, U.S. Census ACS housing vintage, and state regulations. Individual homes may vary.
Compliance Risk Forecast
Probability of future drinking water violations based on historical patterns, enforcement trends, and system size.
95% probability of new violation within 2 years
Based on 13.69 events/year rate. Model uses Poisson distribution with trend and system-size adjustments.
Service Disruption Risk
Critical74% estimated probability of a boil water advisory or service interruption in the next 90 days.
Based on infrastructure age, EPA violation history, flood exposure, and seasonal patterns.
Estimates based on EPA enforcement data, U.S. Census ACS housing vintage, and FEMA flood claims. Not a guarantee of disruption.
Your Water System
ZIP code 18372 in Tannersville, Pennsylvania is served by Brodhead Creek Reg Water Authority (EPA ID: PA2450034). This system provides water to approximately 30,000 people from surface water sources.
There are 4 community water systems serving this area.
Home Safety Score: F (33/100)
Based on water quality violations, lead levels, and radon risk in your area. This score is better than 1% of ZIP codes nationally and 1% in Pennsylvania.
| Factor | Status | Details |
|---|---|---|
| Water Quality | poor | 29 violations, 4 health-based |
| Lead in Water | exceeds | 0.1228 mg/L (EPA action level: 0.015 mg/L) |
| Radon Risk | High | Zone 1 |
| Gas Safety | low | 2 incidents, score 13/100 |
| Wildfire Smoke | low | score 23/100, 5 county fires (5yr) |
| Earthquake Risk | Very Low | score 3.4/50 |
| Superfund NPL | High | nearest 1.4 mi (Butz Landfill), 2 sites within 10 km |
Lead & Copper in Your Water
The EPA requires water systems to monitor lead and copper levels under the Lead and Copper Rule.
| Metal | Measured Level | EPA Action Level | Status | Sample Date |
|---|---|---|---|---|
| Lead | 0.1228 mg/L | 0.015 mg/L | Exceeds action level | N/A |
| Copper | 1.447 mg/L | 1.3 mg/L | Exceeds action level | N/A |
Radon Risk
Radon Zone 1 — High potential (Monroe County)
EPA recommends all homes in this area be tested for radon. Zone 1 indicates the highest radon potential (predicted average indoor radon screening level greater than 4 pCi/L).
CO & Gas Safety
Gas Distribution Risk: Low (score: 13/100)
2 gas distribution incidents recorded in this county since 2004, including 1 fatalities. Most recent: 2020.
The CPSC recommends CO detectors on every level of your home. Have gas appliances inspected annually by a licensed technician.
Wildfire & Smoke Risk
Smoke Risk: Low (score: 23/100)
5 wildfires recorded in this county over the past 5 years. Nearest recent wildfire: 7 km (4 miles).
Monitor air quality at AirNow.gov during fire season (June–November). A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events.
Earthquake & Seismic Risk
Risk Rating: Very Low (score: 3.4/50)
| Metric | Value |
|---|---|
| Risk Score | 3.4 |
| Risk Rating | Very Low |
| Annual Frequency | < 0.001 damaging events/yr |
| Expected Annual Loss | $174K (Relatively Low) |
Monitor seismic activity at the USGS Earthquake Map. Secure heavy furniture, maintain an emergency kit, and know your gas shutoff location.
Superfund Site Proximity
Proximity Risk: High (score: 56/100)
Nearest NPL site: Butz Landfill at 1.4 miles (2.2 km).
| Radius | NPL Sites |
|---|---|
| Within 5 km (3.1 mi) | 1 |
| Within 10 km (6.2 mi) | 2 |
| Within 25 km (15.5 mi) | 4 |
Nearest NPL Sites
- Butz Landfill — 1.4 mi (Construction Complete), listed 03/31/1989
- Route 940 Drum Dump — 5.3 mi (Deleted), listed 07/22/1987
- Brodhead Creek — 8.2 mi (Deleted), listed 09/08/1983
- Tobyhanna Army Depot — 11.2 mi (Construction Complete), listed 08/30/1990
- Palmerton Zinc Pile — 21.3 mi (Active Cleanup), listed 09/08/1983
Search nearby sites at the EPA Superfund Site Search. If you garden or use well water near an NPL site, consider soil and water testing.
Violation Summary
Recent Violations
| Date | Contaminant | Type | Status |
|---|---|---|---|
| September 1, 2025 | Contaminant 0700 | Monitoring | Resolved |
| July 1, 2025 | Copper | Monitoring | Unresolved |
| May 12, 2025 | Lead and Copper Rule | Monitoring | Unresolved |
| April 1, 2025 | Stage 1 DBP Rule | Health-based | Unresolved |
| January 11, 2025 | Lead and Copper Rule | Monitoring | Unresolved |
| September 1, 2024 | Contaminant 0700 | Monitoring | Resolved |
| July 1, 2024 | Copper | Monitoring | Resolved |
| May 11, 2024 | Lead and Copper Rule | Monitoring | Resolved |
| January 11, 2024 | Lead and Copper Rule | Monitoring | Resolved |
| January 1, 2024 | Contaminant 2063 | Monitoring | Resolved |
| January 1, 2024 | Atrazine | Monitoring | Resolved |
| June 13, 2023 | Lead and Copper Rule | Monitoring | Resolved |
| June 1, 2023 | Contaminant 0700 | Health-based | Resolved |
| April 13, 2023 | Lead and Copper Rule | Monitoring | Resolved |
| April 1, 2023 | Contaminant 0700 | Health-based | Resolved |
| April 1, 2023 | Contaminant 0700 | Monitoring | Resolved |
| January 11, 2023 | Lead and Copper Rule | Monitoring | Resolved |
| January 1, 2023 | Atrazine | Monitoring | Unresolved |
Contaminants Detected
The following contaminants have been flagged in EPA records for water systems serving this ZIP code:
| Contaminant | Category | Violations | Health-Based |
|---|---|---|---|
| Contaminant 0700 | Other | 8 | Yes |
| Lead and Copper Rule | Treatment Technique | 7 | No |
| Surface Water Treatment Rule | Treatment Technique | 4 | No |
| Stage 1 DBP Rule | Treatment Technique | 2 | Yes |
| Copper | Inorganic | 2 | No |
| Atrazine | Organic | 2 | No |
| Contaminant 1085 | Other | 1 | No |
| Uranium | Radionuclides | 1 | No |
| Radium-228 | Radionuclides | 1 | No |
| Contaminant 2063 | Other | 1 | No |
Energy Costs in PA
Residential electricity rate: 20.19¢/kWh — 19% above the national average (17.0¢/kWh).
High electricity rates in Pennsylvania make energy-efficient appliances and heat pumps particularly valuable for reducing utility bills.
Energy Sources
Pennsylvania generates 3.3% of its electricity from renewable sources — 24% below the national average of 26.9%. Including nuclear, 33.7% of the state's power is carbon-free (EIA 2025).
| Source | Share |
|---|---|
| Natural gas | 58.3% |
| Nuclear | 30.4% |
| Coal | 7.1% |
| Wind | 1.5% |
| Hydroelectric | 1.1% |
| Solar | 0.8% |
Need help with your water quality?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
Water Systems Serving This Area
| System Name | EPA ID | Population | Source |
|---|---|---|---|
| Brodhead Creek Reg Water Authority | PA2450034 | 30,000 | Surface water |
| Northridge at Camelback | PA2450124 | 330 | Groundwater |
| Village at Camelback | PA2450056 | 309 | Groundwater |
| Mountain View Village | PA2450083 | 100 | Groundwater |
What You Can Do
- Request your water system's Consumer Confidence Report (CCR) — Your utility is required to publish this annually
- Consider a home water test — Independent testing can reveal issues in your specific plumbing
- Install a certified water filter — NSF-certified filters can address specific contaminants
- Contact your water provider — Ask about current treatment and any ongoing remediation
Need help with water testing or filtration?
Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400
Find the Right Water FilterFree tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.
Other Water Quality Reports in Pennsylvania
- 15001 (Aliquippa) — 18 violations
- 15003 (Ambridge) — 26 violations
- 15004 (Atlasburg)
- 15005 (Baden) — 2 violations
- 15006 (Bairdford)
- 15007 (Bakerstown)
- 15009 (Beaver) — 15 violations
- 15010 (Beaver Falls) — 20 violations
- 15012 (Belle Vernon) — 38 violations
- 15014 (Brackenridge) — 1 violation
- 15015 (Bradfordwoods)
- 15017 (Bridgeville)
- 15018 (Buena Vista)
- 15019 (Bulger)
- 15020 (Bunola)
- 15021 (Burgettstown)
- 15022 (Charleroi) — 4 violations
- 15024 (Cheswick) — 3 violations
- 15025 (Clairton)
- 15026 (Clinton) — 14 violations
Nearby Water Quality Reports
- 18348 (Pocono Lake Preserve) — 1 mi
- 18355 (Scotrun) — 2 mi — 4 violations
- 18352 (Reeders) — 2 mi
- 18321 (Bartonsville) — 3 mi
- 18370 (Swiftwater) — 3 mi
- 18332 (Henryville) — 4 mi — 22 violations
- 18349 (Pocono Manor) — 4 mi — 5 violations
- 18320 (Analomink) — 5 mi
- 18344 (Mount Pocono) — 5 mi — 10 violations
- 18360 (Stroudsburg) — 6 mi — 25 violations
Data Sources
This report uses public data from the EPA Safe Drinking Water Information System (SDWIS). View the full compliance record for Brodhead Creek Reg Water Authority (PA2450034) on EPA.gov.
Frequently Asked Questions
Is the tap water in 18372 safe to drink?
Tannersville's water system has recorded 4 health-based violations in the past 5 years. While the system is required to treat water to meet federal standards, you may want to consider additional precautions such as a certified water filter.
Where does 18372's water come from?
The primary water source for this area is surface water. Brodhead Creek Reg Water Authority serves approximately 30,000 people.
How can I get my water tested?
Contact your local water utility for a free water quality report, or hire a certified lab for independent home water testing. The EPA recommends testing annually if you use a private well.
Does 18372 have lead in the water?
EPA Lead and Copper Rule sampling data for water systems serving ZIP code 18372 recorded a lead level of 0.1228 mg/L, which exceeds the EPA action level of 0.015 mg/L. The water system is required to take corrective action. Consider using a certified lead-removal water filter.
What is the radon risk in 18372?
ZIP code 18372 (Monroe County) falls in EPA Radon Zone 1, indicating high radon potential. The EPA recommends all homes in Zone 1 areas be tested for radon. Radon is a naturally occurring radioactive gas that can accumulate in homes and is the second leading cause of lung cancer in the U.S.
USGS reports that 4 of the top compounds applied across the surrounding county are flagged by the EPA for drinking-water monitoring — see the agricultural pesticide-use section
Contaminant Stress Analysis
Statistical envelope (p10/p50/p90) of measured contaminant levels compared to EPA Maximum Contaminant Levels (MCL). Based on enforcement and compliance monitoring data.
All measured values of Lead (LCR 90th) remain below the MCL of 15 PPB.
Pennsylvania Water Quality Overview
ZipCheckup analyzes lab results from 899 water systems across Pennsylvania, covering 16 contaminants from 2 data sources. The most frequently tested contaminants include NEtFOSAA, NMeFOSAA, Pfhxa. Overall, Pennsylvania earns a water quality grade of C (average score: 55/100) across 2,184 ZIP codes. 48% of tested systems have at least one EPA violation on record. If you live in Pennsylvania, review the contaminant table above for your specific water system — state averages may not reflect local conditions.
Score History
Tracking since 2021-12-31 · 59 data points
Safety Score Timeline
Compliance History
Environmental Incidents
Health-Based Violations
Enforcement Actions
Understanding EPA Enforcement
- MCL Violation — Contaminant exceeded the Maximum Contaminant Level set by EPA
- Treatment Technique (TT) — Water system failed to follow required treatment methods
- Formal Enforcement — EPA or state issued a legal order (administrative order, court action, or compliance order)
- Resolved — The water system returned to compliance
Source: EPA Enforcement and Compliance History Online (ECHO). Data from the Safe Drinking Water Information System (SDWIS). Updated quarterly.
PFAS Tested — None Detected
Water serving ZIP code 18372 was tested for PFAS ("forever chemicals") under the federal UCMR5 monitoring program — no PFAS detected.
The EPA Fifth Unregulated Contaminant Monitoring Rule (UCMR5) requires every public water system serving over 3,300 people to test for 29 PFAS compounds and lithium between 2023 and 2025. Systems with no detections at the federal minimum reporting level have provided clean results.
Health Risks from Detected Contaminants
Uranium
High RiskEPA limit: 0.03 mg/L
Kidney toxicity, increased cancer risk
At-risk groups: people with kidney disease, pregnant women, rural residents on private wells in the western US
Removal: reverse osmosis, ion exchange (anion exchange), lime softening · Find a filter →
Radium-228
High RiskEPA limit: pCi/L (combined Radium-226 & 228 ≤ 5 pCi/L)
Bone cancer and leukemia (known carcinogen)
At-risk groups: long-term groundwater consumers, residents in areas with thorium-rich geology
Removal: ion exchange (water softener), reverse osmosis, lime softening · Find a filter →
Atrazine
Moderate RiskEPA limit: 0.003 mg/L
Endocrine disruption, cardiovascular & reproductive effects
At-risk groups: pregnant women, people in agricultural areas, rural communities in the Midwest corn belt
Removal: granular activated carbon (GAC), carbon block filter, reverse osmosis · Find a filter →
Childhood Environmental Risk Score — 18372
Moderate RiskThis ZIP's score is higher than 38% of U.S. ZIP codes and 10% of those in Pennsylvania — a relative ranking, not a verdict on any home.
Risk Factor Breakdown
Water system violation history is the largest contributor to this ZIP's score. A pattern of violations can signal recurring quality issues worth monitoring, and reviewing a system's recent record helps families know what to ask about.
- Children under 6 are most vulnerable to lead exposure — there is no safe level of lead in blood
- Test your home's drinking water, especially if your home was built before 1986
What families can do
Here are calm, practical steps families in this ZIP can consider — informational guidance, not cause for alarm.
No specific actions are flagged for this ZIP. The general guidance above still applies to every family.
Know a family in 18372? A free 30-second ZIP check shows them the same lead, water, and housing data.
Lead Pipe Replacement Funding for Pennsylvania
Key LCRI Deadlines
What This Means for You
- If your home was built before 1986, it may have lead service lines
- Your water utility is required to inventory and replace lead lines at no cost to you
- Contact your water utility to check if your address is in their inventory
Source: EPA DWSRF Lead Service Line Replacement Program, FY2025 Allotment Memorandum.
Active Alerts in Pennsylvania
0 active weather alerts in Pennsylvania. Severe weather can affect your water quality and home safety.
View alerts for Pennsylvania →
Environmental Hazards (9) HIGH
Flood Risk Profile
FEMA Flood Zones Explained
- Zone A / AE — High-risk (100-year floodplain). Flood insurance required for federally backed mortgages
- Zone V / VE — High-risk coastal area with wave action. Strictest building requirements
- Zone X — Moderate-to-low risk (500-year floodplain or minimal flood hazard)
- Zone B / C — Areas of moderate or minimal flood hazard
Air Quality for 18372
Air quality is satisfactory, and air pollution poses little or no risk. Enjoy outdoor activities.
Termite Risk for 18372
Moderate Termite ZoneRequired for VA/FHA loans in select southern counties; not statewide
VA/FHA loan in designated counties will not close without NPMA-33
Termite Damage in the U.S.
- Termites cause an estimated $5 billion in property damage annually in the United States, according to the USDA.
- Standard termite treatment costs $225–$2,500; fumigation for severe infestations: $2,000–$8,000.
- Homeowner insurance typically does not cover termite damage, as it is considered preventable.
What Homeowners Should Know
- Annual termite inspections are recommended in moderate-to-heavy risk zones. Early detection can prevent thousands in repair costs.
- VA and FHA loans require a clear NPMA-33 (Wood Destroying Insect Inspection Report) for closing in most states.
- Warning signs: mud tubes on foundation walls, hollow-sounding wood, discarded wings near windows, and frass (droppings) near baseboards.
- Preventive treatment ($200–$900 per year) is far less expensive than structural damage repair, which averages $3,000 and can exceed $50,000.
- Even in lower-risk zones, subterranean termites can be active. Consider an inspection if purchasing an older home or if you notice warning signs.
Source: USDA Forest Service Termite Infestation Probability (TIP) zones, VA/FHA lender requirements, Pennsylvania pest control regulations. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Pest Risk for 18372
Moderate Pest Pressureticks, termites, bed bugs, stink bugs and carpenter ants
- Lyme disease endemic area
- West Nile activity zone
Required for VA loans in all states; not state-mandated but WDI common in practice
Up to $10,000 per violation
Why This Matters
- Health risks: Mosquitoes transmit West Nile virus (1,000+ U.S. cases annually). Ticks spread Lyme disease (estimated 476,000 cases/year per CDC). Rodent droppings can carry hantavirus.
- Property damage: Carpenter ants and termites cause billions in structural damage annually. Rodents gnaw wiring, creating fire hazards.
- Food safety: Cockroaches and rodents contaminate food preparation areas and can trigger allergies and asthma, especially in children.
- Pennsylvania experiences seasonal pest pressure peaks. Annual inspections help catch infestations early before they become costly.
Common Questions
Source: CDC vector-borne disease surveillance, EPA pesticide regulation data, Pennsylvania pest control board, NPMA pest prevalence maps. Inspection cost estimates reflect typical market rates and may vary by provider, property size, and location. This information is for general guidance only.
Wildfire & Smoke Risk Profile
Wildfire Smoke Safety Tips
- Air purifier with HEPA filter: run in the room where you spend the most time. Close windows and doors during smoke events.
- N95 or KN95 masks: standard cloth and surgical masks do not filter fine particulate matter (PM2.5) from wildfire smoke.
- Seal gaps: use wet towels or tape around doors and windows to reduce smoke infiltration during poor air quality days.
- Monitor AQI: check AirNow.gov daily during fire season. AQI above 100 = unhealthy for sensitive groups; above 150 = unhealthy for everyone.
- Create a clean room: designate one room with the air purifier running, keep it sealed, and limit time outdoors when AQI is elevated.
Protect Your Indoor Air from Wildfire Smoke
A HEPA air purifier can reduce indoor PM2.5 by up to 80% during smoke events. Portable units for a single room start at $80. Whole-home solutions start at $300.
Product links may earn a commission — see our disclosure.
Earthquake & Seismic Risk Profile
Earthquake Preparedness Tips
- Secure heavy furniture: anchor bookshelves, water heaters, and large appliances to wall studs. Unsecured items cause most earthquake injuries.
- Emergency kit: water (1 gallon per person per day for 3 days), non-perishable food, flashlight, batteries, first aid kit, wrench to turn off gas. Keep kits at home and in your car.
- Know how to shut off gas: locate the gas meter shutoff valve and keep a wrench nearby. Gas leaks are a leading cause of post-earthquake fires.
- Drop, Cover, Hold On: during shaking, drop to hands and knees, take cover under a sturdy table, and hold on. Do not stand in doorways or run outside.
- Structural retrofit: homes built before 1980 may need foundation bolting or cripple wall bracing. FEMA's earthquake resources offer guidance on retrofitting.
- USGS ShakeMap: monitor real-time and recent seismic activity at earthquake.usgs.gov.
Build Your Earthquake Preparedness Kit
FEMA recommends every household in a seismic zone maintain a 72-hour emergency kit. Pre-assembled kits start at $40 and include water, food, first aid, and tools.
Product links may earn a commission — see our disclosure.
Mold Risk Assessment for 18372
Moderate RiskSummer months (June–August) present the highest mold risk in 18372, with average humidity reaching 68%. Indoor humidity can be 10–15% higher in poorly ventilated spaces. Winter humidity drops to 68%, reducing but not eliminating risk.
Why Mold Matters
- The CDC and EPA identify mold as a significant indoor health hazard. Common symptoms include respiratory irritation, allergic reactions, and asthma exacerbation.
- Mold begins growing within 24–48 hours on damp surfaces when relative humidity exceeds 60%. Bathrooms, basements, and crawl spaces are most vulnerable.
- Professional mold remediation costs $1,500–$9,000 on average. Homeowner insurance often excludes mold coverage unless caused by a "covered peril."
- Homes built before 1980 typically lack modern vapor barriers and ventilation systems, increasing moisture infiltration risk.
Prevention Recommendations
- Use a dehumidifier to keep indoor humidity below 50%. This is especially important in basements, crawl spaces, and bathrooms in high-humidity areas like 18372.
- Ensure proper ventilation: use exhaust fans in bathrooms and kitchens, and keep attic and crawl space vents unblocked.
- Fix leaks immediately. Even small plumbing leaks can create mold-favorable conditions within 48 hours.
- Monitor indoor humidity with a hygrometer ($10–$20). Target 30–50% year-round.
With 68% average humidity, a dehumidifier is the most effective way to reduce mold risk in 18372. Energy Star-rated units cost $200–$400 and can reduce humidity by 20–30%.
Respiratory Risk Today
High RiskSuperfund Sites & Soil Contamination Risk
Nearest Superfund (NPL) Sites
| Site Name | Distance | Status | Listed |
|---|---|---|---|
|
Butz Landfill
Stroudsburg, Pennsylvania
|
1.4 mi | Construction Complete | 03/31/1989 |
|
Route 940 Drum Dump
Pocono Summit, Pennsylvania
|
5.3 mi | Deleted from NPL | 07/22/1987 |
|
Brodhead Creek
Stroudsburg, Pennsylvania
|
8.2 mi | Deleted from NPL | 09/08/1983 |
|
Tobyhanna Army Depot
Tobyhanna, Pennsylvania
|
11.2 mi | Construction Complete | 08/30/1990 |
|
Palmerton Zinc Pile
Palmerton, Pennsylvania
|
21.3 mi | Active Cleanup | 09/08/1983 |
What Are Superfund NPL Sites?
The National Priorities List (NPL) is the EPA's list of the most contaminated sites in the United States. These sites are eligible for federal cleanup funding under CERCLA (the "Superfund" law). Common contaminants include heavy metals, volatile organic compounds (VOCs), pesticides, and industrial solvents that can leach into soil, groundwater, and air.
- Active Cleanup: EPA is investigating or remediating the site — contamination may still be present.
- Construction Complete: Physical cleanup is done, but long-term monitoring continues.
- Deleted: Site meets EPA cleanup standards and has been removed from the NPL.
Know What's in Your Soil
If you live near a Superfund site, a home soil test kit can detect heavy metals, lead, and other contaminants — especially important if you garden, have children, or use well water.
Product links may earn a commission — see our disclosure.
Agricultural pesticide use in the surrounding county
USGS estimates how many kilograms of agricultural pesticides are applied each year in this ZIP code’s surrounding county, plus the five most-applied compounds. These are county-level use estimates, not a measurement of any pesticide in the tap water served to this ZIP code.
Top compounds by volume
The five compounds applied in the largest amounts across this county. Where the EPA sets a drinking-water reference limit (MCL) for a compound, that limit is shown for context — it is a regulatory reference, not a finding of any concentration in this ZIP code’s water.
-
Moderate water concernGLYPHOSATEHerbicide · 3k kg/yr · EPA drinking-water reference limit: 700 ppb
-
High water concernATRAZINEHerbicide · 1.3k kg/yr · EPA drinking-water reference limit: 3 ppb
-
Low water concernPENDIMETHALINHerbicide · 1k kg/yr
-
High water concernMETOLACHLORHerbicide · 481 kg/yr
-
High water concernSIMAZINEHerbicide · 408 kg/yr · EPA drinking-water reference limit: 4 ppb
4 of the top compounds are ones the EPA flags for drinking-water monitoring — see the drinking-water section above
What this means
- These figures describe pesticide application across the surrounding county, not the drinking water at this address.
- An EPA Maximum Contaminant Level (MCL) is a regulatory reference for how much of a compound is allowed in finished tap water — it is not a finding of contamination at this ZIP code.
- Tested drinking-water results from the local water system — when reported — appear in the drinking-water section of this report.
Methodology: Annual county pesticide-use estimates are from the USGS Pesticide National Synthesis Project, mapped from county FIPS to ZIP code. EPA Maximum Contaminant Levels are reproduced from federal drinking-water regulations and are reference points only.
Informational only. County-level agricultural pesticide-use estimates are not a measurement of any pesticide in the drinking water served by this ZIP code, nor an assessment of health risk. Tested drinking-water results, when reported by the local water system, appear in the drinking-water section above.
Home & Infrastructure (9) MODERATE
Home Buyer Risk Report
An inspection-grade snapshot of public-data risk factors for this ZIP, built to help a buyer decide what to verify before closing.
Public federal data shows a moderate risk profile for this ZIP. Several factors below are worth verifying independently before closing.
Seven-factor inspection checklist
Each factor below is scored 0–100 from public federal data. A higher score means the factor is more worth verifying before you buy.
The local water system's recent EPA violation and contaminant history, along with an independent tap-water test, gives more context.
The FEMA flood zone, whether the property has flooded before, and flood-insurance requirements are key points to review.
Homes built before 1986 may have lead pipes or solder, and pre-1978 homes may have lead paint — a lead inspection adds clarity.
Heating and cooling costs and the age of the HVAC system, along with recent utility bills, give a fuller picture.
Older homes more often have aging plumbing, wiring, and a water heater near end of life — a full inspection adds detail.
The EPA recommends testing every home for radon; homes in EPA Radon Zone 1 have the highest potential.
Local air-quality history is useful context; for sensitive occupants, an HVAC system with good filtration helps.
Nearby hazards
EPA Superfund sites within 10 km: 2. Nearest: Butz Landfill (about 2.2 km away).
ATSDR public-health assessment for nearby sites: Indeterminate Public Health Hazard.
Modeled probability of a local water-service disruption in the next 90 days.
See the 90-day disruption outlookNearest nuclear plant: Susquehanna, about 43 miles away.
Healthcare access
Hospitals reported by CMS Hospital Compare near this ZIP code, with overall federal quality star ratings where CMS publishes one.
Closest hospitals
-
CMS 5-star ratingST Luke's Hospital - Monroe CampusAcute care · 5.7 mi away · ER
-
CMS 3-star ratingLehigh Valley Hospital - PoconoAcute care · 7.9 mi away · ER
Across the rated hospitals within 15 miles, the average CMS overall-quality rating is 4.0 (CMS scale: 1 to 5).
Federal data from CMS Hospital Compare. Distances are straight-line estimates from the ZIP code centroid; ZipCheckup neither ranks nor recommends any hospital.
Inspection-day checklist
Practical items to raise with your inspector, agent, or the seller — tailored to this ZIP's data.
- Test for radon before closing — the EPA recommends it, especially in Radon Zone 1.
- Get a lead inspection — homes built before 1978 may contain lead paint and pre-1986 homes may have lead pipes or solder.
- Review the local water system's recent disruption and violation history with the utility.
- Hire an independent home inspector for a full walkthrough of the property.
- Read the seller's disclosure and any past inspection or repair records.
- Ask for service records for the HVAC system, water heater, and roof.
What this means
- This report consolidates seven home-purchase risk factors and nearby hazards from public federal data into one place.
- Each flagged item is a recommendation to verify independently — not a finding of a defect.
- An independent home inspection remains an essential step before closing.
Methodology: The report combines the home purchase risk score — a seven-factor composite of public federal data — with EPA Superfund, ATSDR, water-disruption, and NRC nuclear-zone proximity datasets. All figures are modeled estimates.
Informational only. This is a modeled summary of public federal data, not a home inspection, an appraisal, or a prediction of defects. Verify any concern with a qualified inspector before a purchase.
Housing Profile for 18372
Based on U.S. Census data (ACS B25034), there are 1,835 housing units in this ZIP code. The median home was built around 1987, making it roughly 39 years old.
When Homes Were Built
What This Means for Home Equipment
Homes from the 1987s are approaching or past their first major equipment replacement cycle:
- Water heater: estimated ~3 years old
- HVAC system: estimated ~5 years old
- Plumbing: likely Copper
Home Value Context
Estimated median home value in this ZIP code based on Census ACS data. Safety remediation costs include water filtration, lead abatement, radon mitigation, and flood insurance where applicable.
Equipment Age Estimate for 18372
Based on Census data, the median home in this ZIP was built in 1987 (~39 years old). 58% of homes were built before 1986.
The EPA Lead and Copper Rule Improvements (LCRI), finalized October 2024, requires all water utilities to:
- By October 2027: Complete a lead service line inventory and notify all customers with lead or unknown lines
- By ~2037: Replace 100% of lead service lines (mandatory 10-year deadline)
- New action level: Lowered from 15 ppb to 10 ppb — more homes now trigger mandatory action
58% of homes in ZIP 18372 were built before 1986 — the year lead solder was banned. If you receive a notification letter from your water utility, your home likely has lead service lines or lead solder connections.
- Get your water tested for lead (request a test kit from your utility at no cost)
- Install a certified lead-reducing filter (NSF/ANSI 53)
- Contact your utility about replacement assistance — costs run $5,000–$15,000, utilities may cover a portion under LCRI
- Have a plumber inspect your service line connection
Likely pipe material: Copper
Estimates based on U.S. Census ACS housing vintage data and typical equipment lifespans. Actual conditions vary by home.
Water Infrastructure Risk
Risk Factor Breakdown
What This Means
The water infrastructure serving ZIP code 18372 shows multiple risk factors. Most homes in this area were built before 1980, meaning plumbing may contain lead solder or galvanized pipes that corrode over time. The state faces a significant infrastructure funding gap of $1,042 per resident over 20 years. Consider testing your tap water, especially if you have an older home.
Infrastructure Decay & Disruption
Water pipe decay
Local water mains are modeled at or past a critical service threshold.
Bridge condition (FHWA NBI)
Bridge figures are from the Federal Highway Administration's National Bridge Inventory. They describe area-level structural ratings, not the safety of any specific bridge.
Bridge condition — FHWA NBI 2024 annual release
Of 315 bridges classified within this ZIP code's surrounding county, 66 are classified Poor by FHWA NBI 2024.
Good (83) · Fair (166) · Poor (66)
FHWA classifies bridges as Good (rating 7-9), Fair (5-6), or Poor (0-4) based on biennial inspections of deck, superstructure, substructure, and culvert components.
Counts are county-level aggregated; multiple ZIP codes within the same county share these counts. No per-bridge or per-structure-ID claim is made.
Source: FHWA National Bridge Inventory, 2024 annual release.
Gas pipeline incident history
PHMSA records 2 reported gas-distribution pipeline incidents on file for this area.
Source: U.S. Pipeline and Hazardous Materials Safety Administration (PHMSA) historical incident data.
This is the modeled probability of a boil-water advisory or water-service interruption in the next 90 days.
See the full service-disruption breakdown →What this means
- This score blends four public federal datasets — water-pipe decay, bridge condition, gas-pipeline incident history, and a 90-day disruption estimate — into one area-level measure of infrastructure stress.
- It describes the infrastructure around a home, not the condition of the home itself, and it is a modeled estimate rather than an engineering assessment.
- Aging water mains raise the chance of breaks and service interruptions; a plumber can inspect a home's own supply line and shut-off valve.
Concerned about aging water lines on your property? — talk to a local expert.
Call (855) 384-4856Paid Partner This is a free service. You will be connected with an independent service provider. We may receive compensation.
Methodology: Water-pipe decay is modeled with an exponential-decay bathtub curve from Census ACS housing age, EPA ECHO compliance records, and EPA infrastructure-needs data. Bridge condition is from the FHWA National Bridge Inventory; gas-pipeline incidents from PHMSA; the 90-day disruption estimate from EPA and FEMA data. The stress score is a weighted composite of these four signals.
All figures are modeled estimates from public federal data. They are not engineering assessments, predictions of failure, or a judgment about any specific structure or utility.
HVAC System Health for 18372
High energy costs in Pennsylvania (20.19¢/kWh) mean an inefficient HVAC system costs you significantly more. Upgrading to a high-SEER unit or heat pump could save 30–50% on heating and cooling bills.
Seasonal HVAC Tips for Pennsylvania
- Schedule furnace tune-up before first cold snap
- Replace air filter (every 1–3 months)
- Check thermostat calibration
- Insulate exposed ductwork in attic/crawlspace
- Seal drafts around windows and doors
- Check carbon monoxide detectors (gas furnace)
- Schedule bi-annual professional inspection
Common HVAC Issues for 1987-Era Homes
- Aging compressor — most compressors last 12–15 years; may need replacement soon
- Duct leaks — connections loosen over time, wasting 20–30% of conditioned air
- Lower SEER rating — systems from 2000s are typically 10–13 SEER vs. today's 15–20+ SEER
- Thermostat upgrades — older thermostats lack programming features that save 10–15% on energy
The Department of Energy requires all NEW furnaces manufactured after December 18, 2028 to meet 95% AFUE (condensing furnaces). Current standard is 80% AFUE.
What this means for you:
- 80% AFUE non-condensing furnaces will no longer be available for purchase
- Condensing furnaces require PVC venting (additional $1,500–$2,500 for retrofit)
- If the furnace is approaching end of life, consider replacing before the deadline to potentially save on installation costs
- Your existing furnace can continue operating — this applies only to NEW equipment
HVAC Questions for 18372
How do I know if my HVAC system needs replacement?
Key signs include: the system is over 15 years old, frequent repairs (more than 2 per year), uneven heating/cooling between rooms, rising energy bills despite normal use, and unusual noises or odors. Based on census data, the median home in 18372 was built in 1987, putting the estimated HVAC system age at ~5 years.
What SEER rating should I look for in a new HVAC system?
As of 2023, the federal minimum is SEER2 15 for central AC in the southern U.S. and SEER2 14 in the north. For Pennsylvania, look for at least SEER 16–18 for good efficiency. Higher SEER ratings (20+) cost more upfront but save more in areas with high electricity rates like Pennsylvania, where rates are above the national average. ENERGY STAR certified units are a reliable starting point.
How much does HVAC replacement cost in Pennsylvania?
A full HVAC replacement (furnace + AC) typically ranges from $5,000–$12,000 depending on system size, efficiency rating, and ductwork condition. Heat pump systems range from $4,000–$10,000. Federal tax credits (25C) cover up to 30% of the cost for qualifying heat pumps and high-efficiency systems. Check our rebates page for Pennsylvania-specific incentives.
What refrigerant does my AC use and why does it matter?
If your AC was installed before 2010, it likely uses R-22, which was banned in 2020 and now costs $50–$150/lb. Systems from 2010–2024 typically use R-410A, which is being phased down (AIM Act 2025). New systems use R-454B or R-32. When your current system needs major repair, the refrigerant type significantly affects whether repair or replacement makes more economic sense.
Should I replace my furnace before the 2028 efficiency deadline?
If the furnace in a home is over 15 years old and the area has a cold/moderate climate, planning ahead is wise. After December 2028, only 95% AFUE condensing furnaces will be available. These require PVC venting — retrofitting an older home for PVC can cost $1,500–$2,500 on top of the furnace price. Replacing before the deadline with a standard 80% AFUE unit may be more cost-effective if the venting isn't PVC-ready.
HVAC age estimate based on U.S. Census ACS housing vintage data and a 17-year replacement cycle. Actual system age varies by home.
Appliance Age Estimates for 18372
Median home built in 1987 (~39 years old). Appliance ages estimated from typical replacement cycles.
1 appliance likely is near or past typical replacement age.
How Water Quality Affects Appliance Lifespan
Water conditions in Tannersville directly impact how long your appliances last.
Homes built before 1996 have likely gone through 2+ full appliance replacement cycles. If original appliances remain, they are well past expected lifespan.
Appliance Maintenance FAQ
How often should I flush my water heater?
Flush your tank water heater at least once a year to remove sediment buildup. In areas with hard water, every 6 months is recommended. Sediment reduces heating efficiency and accelerates tank corrosion, shortening lifespan by 2–4 years.
When should I replace my dishwasher vs. repair it?
If your dishwasher is over 9 years old and the repair costs more than 50% of a new unit, replacement is generally more cost-effective. Common signs: dishes not getting clean, water pooling after cycles, or rust spots on the interior.
Does a water softener really extend appliance life?
Yes. A water softener can extend water heater lifespan by up to 30% and reduce dishwasher and washing machine maintenance by preventing mineral scale buildup on heating elements, valves, and spray arms. The Battelle Memorial Institute found that softened water kept water heaters at original factory efficiency over a 15-year period.
Estimates based on U.S. Census housing vintage data and manufacturer-average replacement cycles. Actual appliance age depends on renovation history and maintenance.
Electrical Safety for 18372
Median home built in 1987 (~39 years old).
Common Electrical Issues for 1987-Era Homes
- Aging circuit breakers — breakers can weaken over time and fail to trip during overloads, creating fire hazards
- Insufficient circuits — homes from this era may lack dedicated circuits for kitchen, bathroom, and laundry areas
- Missing GFCI/AFCI protection — current code requires GFCI in wet areas and AFCI in bedrooms; older homes often lack both
- Outdated panel capacity — 100–150 amp panels may be insufficient for modern loads (heat pumps, EV charging, home office)
⚠️ Insurance Compliance Alert
58% of homes in 18372 were built before 1986 — the era when Federal Pacific (FPE StabLok), Zinsco, and Challenger electrical panels were commonly installed.
These panels have a documented 60%+ breaker failure rate and are refused by major insurance companies including State Farm, Allstate, and Citizens (FL).
If you receive an insurance non-renewal notice or 4-point inspection failure:
- Typical deadline: 30 days to replace panel
- Replacement cost: $1,500–$4,000
- Failure to replace: insurance cancellation → mortgage default risk
Insurance blacklist: State Farm, Farmers, Allstate, USAA, Mercury, Citizens (FL), Nationwide.
When to Call an Electrician
- Burning smell from outlets or panel
- Frequent breaker trips
- Sparking or discolored outlets
- Buzzing sounds from wiring or panel
- Before buying a home (especially pre-1980)
- After any water damage or flooding
- Before adding major appliances or EV charger
- If your panel is 25+ years old
Electrical Safety Tips
- Never use a fuse with a higher amperage rating than the circuit is designed for
- Label all breakers clearly in your electrical panel
- Keep 3 feet of clearance in front of your electrical panel
- Test GFCI outlets monthly using the built-in test button
- Replace any cracked or warm outlet covers immediately
- Do not daisy-chain power strips or extension cords
Homes built before 1996 should have their electrical panel and GFCI protection reviewed, especially if no upgrades have been made.
Electrical Safety Questions for 18372
How do I know if my electrical panel needs an upgrade?
Key signs include: frequent breaker trips, a panel over 25 years old, fuses instead of circuit breakers, visible rust or corrosion, and a panel rated below 200 amps if you have modern appliances, HVAC, or an EV charger. Based on census data, the median home in 18372 was built in 1987 — homes of this age often have panels that don't meet current electrical demands.
How much does an electrical panel upgrade cost?
A panel upgrade from 100 to 200 amps typically costs $1,500–$4,000 depending on your location and the complexity of the work. If the meter base or service entrance also needs replacement, costs can reach $4,000–$6,000. Rewiring a full home (common in pre-1960 homes) ranges from $8,000–$15,000+ depending on size and accessibility.
Is aluminum wiring dangerous?
Aluminum wiring itself is not inherently dangerous, but connections between aluminum wiring and copper devices (outlets, switches) can overheat due to differential thermal expansion. The Consumer Product Safety Commission (CPSC) found that homes with aluminum wiring are 55 times more likely to have fire-hazard conditions. If your home has aluminum wiring, a qualified electrician can install COPALUM or AlumiConn connectors to make connections safe.
Is my home likely to have a Federal Pacific or Zinsco panel?
These panels were installed primarily between 1960 and 1985. Based on census data, 58% of homes in 18372 were built during this era. If your home was built in this period and the panel has never been replaced, there is a meaningful chance it contains an FPE StabLok or Zinsco panel. Look for the brand name on your breaker panel door.
Electrical risk assessment based on U.S. Census ACS housing vintage data. Actual wiring and panel condition varies by home and renovation history.
Septic System Requirements in Pennsylvania
✓ No Statewide MandateVaries by municipality. Many townships require inspection at property transfer under Act 537 planning.
Penalties set by local ordinance. State does not enforce point-of-sale inspections.
What Homeowners Should Know
- Approximately 1 in 5 U.S. households relies on a septic system for wastewater treatment.
- Regular pumping every 3–5 years is recommended by the EPA to prevent system failure.
- A failed septic system can cost $7,000–$15,000 or more to replace, depending on system type and soil conditions.
- If you are selling a property in Pennsylvania, check your state and local requirements before listing.
- Signs of septic failure include slow drains, sewage odors, and standing water near the drain field.
Source: Pennsylvania environmental and health department regulations. Cost estimates reflect typical market rates and may vary by provider, system size, and location. This information is for general guidance only—contact your local health department for requirements specific to your property.
Underground Oil Tank: Low Risk for 18372
Pennsylvania regulates underground heating oil tanks, but only 0% of homes in 18372 were built before 1980 — the era when underground steel tanks were commonly installed. The risk of encountering a buried oil tank in this ZIP code is relatively low. If purchasing a pre-1980 home, a tank sweep is still recommended.
Source: Pennsylvania environmental regulations (Act 32 of 1989; 25 Pa. Code Chapter 245), U.S. Census ACS housing vintage data.
CO & Gas Safety Profile
CO & Gas Safety Tips
- Install CO detectors on every level of your home and near sleeping areas. Replace batteries annually and units every 5-7 years.
- Know gas leak signs: rotten egg smell, hissing sounds near gas lines, dead vegetation near pipelines, bubbling in standing water.
- Annual inspection: have a licensed technician inspect gas appliances (furnace, water heater, stove) every year.
- Emergency: if you smell gas, leave immediately, do not use electrical switches, and call 911 or your gas company from outside.
Protect Your Home from Carbon Monoxide
The CPSC recommends a CO detector on every level. Battery-operated models start at $20. Smart detectors with app alerts start at $35.
Product link may earn a commission — see our disclosure.
Remodeling Permit Requirements in Pennsylvania
ⓘ Permits RequiredStructural, electrical, plumbing, mechanical. Uniform Construction Code applies statewide since 2004.
Fines up to $500/day, stop-work orders, mandatory correction
Why This Matters
- Unpermitted work can reduce your home's appraised value by 10–20% and complicate or block a sale entirely.
- Homeowner insurance may deny claims for damage caused by or related to unpermitted renovations.
- Buyers' lenders may require proof of permits before approving a mortgage, especially for kitchens, bathrooms, and structural changes.
- Unpermitted electrical and plumbing work is a leading cause of house fires and water damage — permits exist to ensure safety inspections.
- If you are planning remodeling work in Pennsylvania, contact your local building department before starting any project that alters structure, electrical, plumbing, or mechanical systems.
Remodeling Permit Questions for 18372
What remodeling work requires a permit in Pennsylvania?
In Pennsylvania, permits are generally required for any work that alters the structure, electrical wiring, plumbing, or mechanical systems of a home. This includes kitchen and bathroom renovations involving plumbing or electrical changes, wall removal, room additions, window enlargements, re-roofing, and HVAC replacement. Purely cosmetic work — painting, flooring, cabinet refacing without plumbing changes — typically does not require a permit. Always check with your local building department, as municipal requirements may be stricter than state minimums.
What happens if I remodel without a permit in Pennsylvania?
Working without a required permit in Pennsylvania can result in Fines up to $500/day, stop-work orders, mandatory correction. Beyond legal penalties, unpermitted work creates problems when selling: buyers' home inspectors and appraisers flag unpermitted additions, lenders may refuse financing, and title companies may require permits to be obtained retroactively — often at 2–3 times the original permit fee. In serious cases, you may be required to open walls for inspection or demolish non-compliant work.
How much does a remodeling permit cost in Pennsylvania?
Remodeling permit fees in Pennsylvania typically range from $100 to $2500, depending on the scope and value of the project. Most jurisdictions calculate fees as a percentage of the project's estimated construction cost (usually 1–2%) or use a flat fee schedule based on project type. Electrical and plumbing sub-permits may be billed separately. Contact your local building department for an exact fee quote before starting work.
Permit requirements based on Pennsylvania building codes and ICC adoption data. Costs reflect typical municipal fee schedules and may vary by jurisdiction, project scope, and valuation. This information is for general guidance only — contact your local building department for requirements specific to your project.
Home maintenance concerns detected — talk to a local expert.
Call (855) 384-4856Paid Partner This is a free service. You will be connected with an independent service provider. We may receive compensation.
Cost & Community (5) OK
True Cost of Ownership
How this ZIP compares
Where the estimate comes from
Show all 5 factors
5-year equipment outlook
No major equipment is flagged for likely replacement within five years.
What this means
- This is a modeled estimate of how much more — or less — a household here may spend each year on risk-related costs such as insurance, mitigation, testing, and maintenance, compared with a typical US ZIP.
- It is a comparison figure for context, not a bill, a quote, or financial advice.
- The 5-year equipment ranges above are separate one-time replacements, not part of the annual figure.
Methodology: Each of 13 risk verticals is assigned a dollar figure from public federal data; the total is the modeled annual difference from a median-risk US ZIP. The 5-year equipment outlook flags major home equipment whose estimated age is within five years of its typical service life; figures are national-average installed-cost ranges.
Estimates are modeled from public federal data. They are not quotes, prices, or financial or insurance advice.
Tax Burden in Pennsylvania
State tax rates affect cost of ownership. Here's how Pennsylvania compares to national averages.
Source: Tax Foundation 2024. Income tax = top marginal rate. Sales tax = state + avg local. Property tax = effective rate on home value.
Energy Costs in Pennsylvania
Residential electricity rate: 20.19¢/kWh — 19% above the national average (national avg: 17.0¢/kWh · EIA, December 2025)
Pennsylvania Energy Mix
Source: EIA Form 923, 2025 data. Renewable = solar + wind + hydro + geothermal.
Electric Utility for 18372
Source: U.S. Energy Information Administration, Form EIA-861 (2024 data). EIA ID: 14715.
Home Energy Audit for 18372
The Inflation Reduction Act provides up to $8,000 in rebates and $3,200 in annual tax credits for home energy upgrades — but many provisions phase down or expire after 2032. A professional energy audit is the first step to qualifying for these incentives. Homes in 18372 average ~39 years old, making energy audits especially impactful.
What a Home Energy Audit Covers
- Insulation levels in attic, walls, and basement
- Air leaks around windows, doors, and ducts
- Blower door test (measures total air leakage)
- HVAC efficiency and age assessment
- Water heater type and condition
- Lighting and appliance energy use
- Carbon monoxide and combustion safety
- Moisture and ventilation assessment
- Gas leak detection
- Prioritized list of recommended upgrades
- Estimated cost and savings for each upgrade
- Rebate and tax credit eligibility report
- The average home energy audit identifies $200–$400/year in savings (DOE)
- Properly sealed and insulated homes save 15% on heating and cooling costs (DOE)
- Heat pump upgrades can reduce heating costs by 30–50% compared to electric resistance
- ENERGY STAR certified windows save $101–$583/year compared to single-pane windows
- Weatherization assistance programs are available for income-qualifying households
Homes in 18372 are ~39 years old on average — older homes typically have the most to gain from an energy audit due to outdated insulation, single-pane windows, and aging HVAC systems.
PPL Electric Utilities Corp (Investor-owned) serves 18372. Your local residential rate is 17.0¢/kWh , which is above the national average — making energy efficiency improvements even more valuable . Many utilities offer additional rebates on top of federal IRA incentives — ask your energy auditor about programs from PPL Electric Utilities Corp.
Under the Inflation Reduction Act. Income limits apply for HEEHRA rebates. Tax credits require tax liability. IRS details →
To claim the $150 federal tax credit, your energy audit must meet DOE standards (10 CFR 440.21) and be performed by a qualified auditor. A DOE-compliant audit includes:
- Blower door test to measure air infiltration
- Infrared thermography to identify insulation gaps
- Combustion safety testing for gas appliances
- Written report with prioritized, cost-effective upgrade recommendations
Energy Audit Questions for 18372
How much does a home energy audit cost?
A professional home energy audit typically costs $150–$400 depending on the size of your home and the depth of testing. The Inflation Reduction Act provides a $150 tax credit for qualifying audits performed by a certified auditor, effectively covering a significant portion of the audit cost. Some utilities also subsidize audits for their customers — check with PPL Electric Utilities Corp for local programs.
What is the difference between an energy audit and a home inspection?
A home inspection (done during a home sale) evaluates structural and safety conditions. An energy audit specifically measures how your home uses energy and identifies efficiency improvements. Energy audits use specialized tools like blower doors, infrared cameras, and duct blasters that are not part of a standard home inspection. The audit produces a prioritized list of upgrades with estimated costs and savings.
How much can I save after an energy audit?
According to the U.S. Department of Energy, the average audit identifies $200–$400/year in savings. Actual savings depend on your home's age, current insulation, HVAC efficiency, and local energy rates. At current rates in Pennsylvania, the average home spends approximately $2,120/year on electricity — a 15–25% reduction through audit-recommended upgrades could save $318–$530 annually. With homes in 18372 averaging ~39 years old, there is likely significant potential for improvement.
What rebates and tax credits are available for energy upgrades?
The Inflation Reduction Act (IRA) provides two types of incentives: (1) Tax credits up to $3,200/year for heat pumps ($2,000), insulation ($1,600), windows ($600), and the audit itself ($150); and (2) HEEHRA rebates for income-qualifying households — up to $8,000 for heat pumps, $1,600 for insulation, $2,500 for electrical panels, and $840 for heat pump dryers. Solar panels qualify for a separate 30% tax credit through 2032.
Do I need an energy audit before installing solar panels?
An energy audit is not legally required before installing solar, but the DOE strongly recommends it. Reducing your home's energy consumption before adding solar means you need a smaller (cheaper) system to cover your needs. An audit typically identifies 15–30% in energy reductions through insulation, air sealing, and HVAC improvements — which directly reduces the size and cost of a solar installation.
How long does a home energy audit take?
A comprehensive energy audit takes 2–4 hours for a typical single-family home. The auditor will inspect the attic, basement, walls, windows, HVAC system, water heater, and ductwork. Diagnostic tests (blower door, infrared scan) add precision to the findings. You will receive a written report within 1–2 weeks with prioritized recommendations and estimated costs.
Source: U.S. Energy Information Administration (EIA), U.S. Department of Energy (DOE), Inflation Reduction Act of 2022 (P.L. 117-169).
Safety Updates for Tannersville, Pennsylvania
Violations & Enforcement Timeline
View all 14 records
Related Anomalies
Recent Product Recalls
Recent CPSC recalls for plumbing and HVAC products that may affect homes in your area.
Superbobi 7 3/8 Inch Pool Drain Covers
Shenzhen Jiangtou Technology Co. · 2026-05-14
Electric Kettles (ENFINIGY 1.5 l and ENFINIGY Pro 1.5 l)
ZWILLING J. A. Henckels Aktiengesellschaft · 2026-05-14
Electric Start Pressure Washers
Generac Power Systems Expands · 2026-05-14
1-K Kerosene Heater Fluid Portable Fuel Containers
Alliance Chemical · 2026-04-30
Protect Your Home in Tannersville
Based on local data for ZIP 18372, these services may benefit homeowners in your area.
Based on local data for your area. Use the tools below to explore your options.
Home & Flood Insurance
Tannersville has 17 FEMA flood claims on record. Standard homeowner policies don't cover flood damage — make sure you're protected.
Typical cost: Flood insurance: typically $700–$1,500/year in flood-prone areas
Check Your Flood Zone (Free)FEMA flood map lookup — see if your property is in a flood zone
Free tip: Check your FEMA flood zone at msc.fema.gov (free lookup)
Gutter Installation & Repair
Homes in 18372 were built around 1987 on average. Aging gutters can cause foundation damage, basement flooding, and mold — a professional assessment can prevent costly repairs.
Typical cost: Gutter installation: typically $1,000–$2,500 for a standard home
Estimate Your Home Maintenance CostsService recommendations are based on public data for this ZIP code (FEMA, Census ACS, NWS). Actual needs vary by property. By calling, your information will be shared with an independent service provider. ZipCheckup may receive compensation. Cost estimates are approximate and vary by property, condition, and contractor.
Take Action
Concerned about these findings? Contact your local elected officials to ask what is being done about water quality in your area.
Email Your RepresentativeDon't know who to contact? Find your local representative at usa.gov/elected-officials
Frequently Asked Questions
Is the tap water in 18372 safe to drink?
Based on EPA SDWIS data, Tannersville's primary water system (Brodhead Creek Reg Water Authority) has 29 recorded violations in the past 5 years, including 4 health-based. Check the full report above for details.
Where does 18372's water come from?
The primary water source for ZIP code 18372 is Surface water. Brodhead Creek Reg Water Authority serves approximately 30,000 people.
How can I get my water tested in Tannersville?
Contact your local water utility (Brodhead Creek Reg Water Authority) for a free Consumer Confidence Report, or hire a certified lab for independent home water testing. The EPA recommends annual testing if you use a private well.
Is lead a concern in 18372 tap water?
The most recent lead sampling for 18372 recorded 0.1228 mg/L. The EPA action level is 0.015 mg/L. This result exceeds the EPA action level — consider using a certified lead-reducing filter.
What is the radon risk for 18372?
18372 falls in EPA Radon Zone 1 (High risk), located in Monroe County. Zone 1 indicates the highest radon potential. Testing your home is recommended regardless of zone.
Are there flood risks in ZIP 18372?
Yes. FEMA records show 17 flood insurance claims filed in ZIP code 18372, with the dominant flood zone being AE. Review FEMA flood maps for your specific property.
Nearby ZIP Code Reports
Water quality comparison for ZIP codes near 18372
| ZIP Code | City, State | Distance | Grade | Violations |
|---|---|---|---|---|
| 18348 | Pocono Lake Preserve, PA | 1.3 mi | D | 0 |
| 18355 | Scotrun, PA | 1.9 mi | D | 4 |
| 18352 | Reeders, PA | 2.0 mi | D | 0 |
| 18321 | Bartonsville, PA | 3.1 mi | D | 0 |
| 18370 | Swiftwater, PA | 3.1 mi | D | 0 |
| 18332 | Henryville, PA | 3.7 mi | C | 22 |
| 18349 | Pocono Manor, PA | 4.1 mi | F | 5 |
| 18320 | Analomink, PA | 4.9 mi | D | 0 |
| 18344 | Mount Pocono, PA | 5.4 mi | D | 10 |
| 18360 | Stroudsburg, PA | 5.7 mi | F | 25 |
Nearby ZIP Code Reports
2026 Rankings for Your Area
Overall safety breakdown
Home Safety Score →Find the right water filter
Water Filter Matcher →Compare filters, tests & services
Compare My Options →Compare with another ZIP
Compare Tool →2026 Rankings
ZIP 18372 scores in the bottom tier nationally.