Monitoring Violations MA

Athol Dpw Water Division

EPA ID: MA1015000 · 10,418 people served · 2 ZIP codes

The EPA enforcement database lists 2 active violations for Athol Dpw Water Division — a provider that delivers drinking water to approximately 10,418 people and has not yet formally resolved those findings.

Data: EPA SDWIS Last verified: 2026-04-02

C · 66
Avg Safety Score
10,418
People Served
2
ZIP Codes Served
2
Violations (5yr)
Groundwater
Water Source
0.0036 mg/L
Max Lead Level
Zone 1
Radon Risk · High
1
Contaminants Flagged
$291K
Median Home Value in Service Area

Service Area Map

Coverage area for Athol Dpw Water Division Source: EPA SDWIS service area boundaries.

Service area boundary — Grade C

Service Area Demographics

$85,110
Median Household Income
15,362
Service Area Population
22%
Disadvantaged Population
30th
Poverty Percentile
60th
Energy Burden Percentile
70%
Pre-1986 Housing

The Athol Dpw Water Division serves a community with a median household income of $85,110 and an estimated 15,362 residents across its service area. Approximately 70% of housing stock was built before 1986, which increases the likelihood of lead service lines and older plumbing.

💧 Where Does Your Water Come From?

Groundwater

Athol Dpw Water Division's water is pumped from underground aquifers. Groundwater is naturally filtered through rock and soil, but it can be vulnerable to PFAS contamination, nitrates from agriculture, and industrial chemicals that seep into the water table.

Elevated Risk
Source Contamination Risk
40th
Wastewater Discharge Proximity
60th
Superfund Site Proximity

About 1% of homes in Worcester County, Massachusetts rely on private wells rather than public water systems. Private well owners are responsible for their own water testing and treatment.

Superfund Proximity Note: This service area ranks in the 60th percentile nationally for proximity to Superfund (NPL) sites. Groundwater sources near contaminated sites may face elevated risk from industrial chemicals.

Infrastructure Risk

63 yr
Avg Pipe Age
Galvanized Steel or Copper
Pipe Material
8 yr
Est. Remaining Life
Moderate Wear
Decay Status
Installed 89% of expected lifespan used End of life

Detected Contaminants

How Athol Dpw Water Division compares to EPA limits

What This Means For You

Consumer Confidence Report Rule at 2 mg/L exceeds the EPA maximum of mg/L.

PFAS Detected in Service Area

PFAS ("forever chemicals") have been detected in water serving this system's area. 1 detection recorded.

State limits: PFAS6: 0.02 ppt
Health concern: PFAS are linked to cancer, thyroid disease, immune suppression, and developmental effects. They do not break down naturally.
Recommended filter: Reverse osmosis (RO) or activated carbon filters certified for PFAS removal. Find the right filter →

Comparable Water Systems

Similar-sized systems in Massachusetts

C 2 violations
C 0 violations
Ware Water Department
10,066 people
B 0 violations
B 0 violations
C 0 violations

Estimated Remediation Costs

Average estimated costs across ZIP codes served by this system

Radon Mitigation Flood Insurance PFAS Treatment
Radon Mitigation $1,200
Flood Insurance $600
PFAS Treatment $250
Total Estimated Cost $2,050

Based on national averages for common remediation projects. Actual costs vary by property. Only issues flagged by EPA, FEMA, or state data for each ZIP code are included.

Cost of Inaction

If water quality issues in this service area are not addressed, the estimated financial impact per household is:

Estimated Healthcare Costs $500

Annual per household (CDC est.)

PFAS Exposure — Lifetime Cost $1,000

Per person (emerging research est.)

Estimated Cumulative Cost Per Household

5 years
$2,665
10 years
$5,330
20 years
$10,660

Compare: Estimated remediation cost is $2,050 (one-time) vs. $5,330 in estimated inaction costs over 10 years.

Estimates based on published EPA, CDC, and peer-reviewed research. Individual costs vary by household size, property, and health factors. These are conservative lower-bound estimates intended for awareness, not financial advice.

System Overview

Athol Dpw Water Division (EPA ID: MA1015000) is a community water system in Massachusetts that serves approximately 10,418 people from groundwater sources.

This system provides water to 2 ZIP codes across 2 communities.

Average Home Safety Score: C (66/100)

Based on water quality violations, lead levels, and radon risk across all ZIP codes served by this system.

Violation History

2 monitoring/reporting violations recorded. These are procedural violations (missed tests or late reports), not necessarily water safety issues.

Contaminants Detected

The following contaminants have been flagged in EPA records for this water system:

Contaminant Category Violations Health-Based
Consumer Confidence Report Rule Reporting Failure 2 No

Lead & Copper

EPA Lead and Copper Rule sampling data for ZIP codes served by this system:

ZIP Code Lead Level Exceeds Limit Sample Date
01331 0.0036 mg/L No N/A
01368 0.0006 mg/L No N/A

Radon Risk in Service Area

Dominant radon zone for ZIP codes served by this system: Zone 1 (High Risk)

The EPA recommends testing homes in Zone 1 and Zone 2 areas for radon.

Need help with your water quality?

Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400

Find the Right Water Filter

Free tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.

ZIP Codes Served

Coverage: Service area ZIP codes sourced from EPA Community Water System Service Area Boundaries v3 (March 2026 release). These ZIPs reflect the actual deployment footprint recorded by MA or modeled from parcel and building-footprint data.

Data Sources

This report uses public data from the EPA Safe Drinking Water Information System (SDWIS). View the full compliance record for Athol Dpw Water Division (MA1015000) on EPA.gov.

Frequently Asked Questions

Is Athol Dpw Water Division water safe to drink?

Athol Dpw Water Division has only monitoring/reporting violations, which are procedural in nature. The system meets federal health-based standards.

How many people does Athol Dpw Water Division serve?

Athol Dpw Water Division serves approximately 10,418 people across 2 ZIP codes in Massachusetts.

Where does Athol Dpw Water Division get its water?

The primary water source is groundwater.

Contact Your Water Utility

Public-record contact information for the water utility serving this system. Use these channels to request water quality reports, ask about service, or report issues directly.

Phone
978-721-8448
ZipCheckup is not affiliated with this water utility, does not act as its agent, and does not provide customer support for it. Contact details shown are public-record information from CCR filings. For service issues, contact the utility directly using the information above.
Address
584 Main St., Room 24, Athol, MA 01331

Contact information from Town of Athol Water Division Consumer Confidence Report.

ZipCheckup is not affiliated with this water utility, does not act as its agent, and does not provide customer support for it. Contact details shown are public-record information from CCR filings. For service issues, contact the utility directly using the information above.

Water Source & Treatment

Where this water originates and how it's treated before reaching your tap.

Source
Groundwater
Drawn from underground aquifers via wells.
Disinfectant used
Chlorine
Treatment chemicals reported
chlorinehypochlorite

Source: Town of Athol Water Division Consumer Confidence Report.

ZipCheckup is not affiliated with this water utility. Treatment and source data are sourced from the utility's published CCR filings.

Source water assessment from Town of Athol Water Division Consumer Confidence Report:
The Town of Athol has a source water assessment plan to protect its water supplies. Restrictions are in place to prevent hazardous materials and facilities from being allowed within established protection zones. Zone II is the Department of Environmental Protection approved primary recharge area for the aquifer.

Treatment regime

How this utility classifies its treatment process and what each reported treatment chemical does.

Treatment classification
Multi-stage
Multiple treatment stages — typically coagulation, filtration, and disinfection. Common for surface-water systems requiring removal of particulates, microorganisms, and dissolved organic compounds before disinfection.

Treatment chemicals and what each one does

Chemical names are reported verbatim by the utility. Purpose categories are ZipCheckup annotations based on standard drinking-water treatment practice.

Disinfectant
Inactivates bacteria, viruses, and parasites in the treated water.
chlorine
Other reported chemicals
Reported by the utility but not in our annotation dictionary.
hypochlorite

Watershed exposure sources reported

Land-use and natural conditions identified in the utility's source-water assessment as potential contamination sources upstream of treatment.

AgricultureIndustrial activityResidential land useStorage tanksSeptic systemsUrban stormwater runoffWastewater dischargesFertilizer runoffOil and gas productionMiningFarmingFire-fighting foams

Treatment classification and chemical list sourced from Town of Athol Water Division Consumer Confidence Report.

Treatment intensity is a ZipCheckup-derived classification based on the chemicals and processes the utility reports. Chemicals and contamination sources are taken verbatim from the utility's CCR filing. Routine federal monitoring and contaminant testing shown elsewhere on this page determine whether the water meets safety standards, not the treatment classification.

Federal UCMR5 PFAS Monitoring: Tested Clean

This water system was tested under the federal EPA Unregulated Contaminant Monitoring Rule (UCMR5). No PFAS compounds were detected.

Samples collected
116

Current MCL reflects the lowest state-enforceable limit (NYS 10 ppt for PFOA/PFOS, effective August 2020). The federal final MCL of 4 ppt for PFOA/PFOS (EPA April 2024 rule) is not enforceable until April 2029. Detections above 4 ppt but below 10 ppt are below current MCL but above the future federal limit.

Source: U.S. EPA UCMR5 (Unregulated Contaminant Monitoring Rule, 5th cycle) — per-system federal sampling, 2023–2025. EPA UCMR5 monitoring program →

Understand PFAS health context and filtration →

PFAS Substances Detected in This System

This water system's Consumer Confidence Report disclosed the following PFAS compounds. Levels are from the utility's most recent reporting cycle.

Substance Detected level EPA limit Status
PFAS
Not yet EPA-regulated
5.2 ppt 20 ppt Below EPA limit

In April 2024, EPA finalized the first National Primary Drinking Water Regulation for six PFAS. Public water systems have until 2029 to comply. EPA — PFAS regulation overview →

Source: Consumer Confidence Report disclosed by Town of Athol Water Division.

ZipCheckup is not affiliated with this water utility. PFAS detection data is sourced from public Consumer Confidence Reports filed by the utility itself.

Learn more about PFAS health effects and filtration →

Lead service line replacement plan from Town of Athol Water Division Consumer Confidence Report:
The Town of Athol is conducting a Lead Service Line Inventory and Replacement Program. Consumers are asked to help by uploading photos of their service lines using the Mass Lead Service Line Identification (MA-LSLI) app or by scheduling a free in-home survey.

Lead Service Line Replacement Tracker

This water utility's lead service line (LSL) replacement program is tracked from public Consumer Confidence Report filings. Email signup notifies subscribers when the utility files an updated replacement plan or progress milestone.

Get notified on replacement progress

Subscribers receive an email when this utility updates its LSL plan, files a milestone report, or adjusts replacement timelines. No marketing, no third-party sharing.

By submitting you agree to Privacy Policy. Unsubscribe anytime via the link in any email.

Town of Athol Water Division

ZipCheckup is not affiliated with this water utility. LSL replacement-program data is sourced from public CCR filings published by the utility. Subscription notifications are based on automated parsing of subsequent CCR releases.

Learn more about Lead and Copper Rule replacement requirements →

Lead Service Line Inventory

Utility-reported lead service line presence and tap-sample lead level under federal LCRI requirements:

None reported
Lead Service Lines Reported
0.0024 mg/L
Tap Sample Lead Level

Below federal action level (0.015 mg/L)

MassDEP reports utility-level presence flag and tap-sampling without per-line breakdown. Customers should inquire with the utility about service line material at a specific address.

Federal LCRI rule (effective October 2024) requires every public water system to inventory its service lines and complete lead-line replacement within 10 years.

Federal Regulatory Status · 2026Q1
LCRR inventory submission: Did not report any required service line types
Latest tap sample on 2025-06-01 did not exceed the federal lead action level.
Population served: 10,587
Reported to Massachusetts

Source: MassDEP LCRR Service Line Inventory · Submitted 2024

ZipCheckup is not affiliated with the utility or state agency. Inventory figures render verbatim from the public LCRI submission cited above; ZipCheckup does not perform inspections or replacements.

Learn about lead in drinking water →

Aesthetic water quality

These measurements describe the look, taste, and feel of the water this utility delivers. They are not contaminant violations — they sit alongside federal Secondary Maximum Contaminant Levels (SMCLs) which the EPA publishes as non-enforceable guidance.

pH
7.58
How acidic or basic the water is on a 0-14 scale. Drinking water is typically near neutral.
EPA secondary range: 6.5 – 8.5
Fluoride
0.82 ppm
Utility adds fluoride
Measured fluoride concentration in parts per million.
EPA secondary MCL: 2.0 ppm
Total dissolved solids
201 ppm
Mineral content remaining after evaporation, including calcium, magnesium, sodium, and other dissolved substances.
EPA secondary MCL: 500 ppm

Aesthetic measurements from Town of Athol Water Division Consumer Confidence Report.

Aesthetic measurements are reported by the utility from its annual sampling. EPA Secondary MCLs are advisory thresholds — values outside them indicate aesthetic concerns such as taste or appearance, not health violations. Federal contaminant testing is shown in the sections above.

Frequently Asked Questions

Is water from Athol Dpw Water Division safe to drink?
Athol Dpw Water Division has a C safety grade based on 2 recorded violations. Some contaminants may exceed EPA limits — independent testing is recommended.
What contaminants are in Athol Dpw Water Division's water?
Detected contaminants include Consumer Confidence Report Rule. Each is compared against EPA maximum contaminant levels (MCLs) in the detailed breakdown above.
Should I use a water filter?
Given 1 contaminant above EPA limits, a certified water filter can provide an extra layer of protection. The best type depends on specific contaminants in your water.
How many people does Athol Dpw Water Division serve?
Athol Dpw Water Division serves approximately 10,418 people with drinking water across 2 ZIP codes.
What is Athol Dpw Water Division's water source?
Athol Dpw Water Division draws water from groundwater sources. Source type affects which contaminants are most likely to be present.
Is there lead in Athol Dpw Water Division's water?
The maximum detected lead level is 0.0036 mg/L. This is within EPA action level guidelines.
What is the demographic profile of Athol Dpw Water Division's service area?
The Athol Dpw Water Division service area has a median household income of $85,110. Demographic data is sourced from the U.S. Census Bureau and EPA EJScreen.
Where does Athol Dpw Water Division get its water?
Athol Dpw Water Division's water is pumped from underground aquifers. Groundwater is naturally filtered through rock and soil, but it can be vulnerable to PFAS contamination, nitrates from agriculture, and industrial chemicals that seep into the water table. Based on violation history and environmental factors, the source contamination risk is currently elevated.

What You Can Do

1

Test your water

Home test kits can detect lead, bacteria, and other contaminants at your tap. Find the right filter →

2

Check your specific ZIP code

Water quality can vary within a system. View nearest ZIP report →

3

Contact your utility

Athol Dpw Water Division (EPA ID: MA1015000) — request the latest Consumer Confidence Report or ask about specific contaminants.

Home Water Systems Massachusetts Athol Dpw Water Division

Get safety alerts for Athol Dpw Water Division, Massachusetts

Free updates when EPA data changes for this area. No spam.

Unsubscribe anytime. Privacy Policy.

Share This Page

X Facebook
Violations found — check filter options Free tool — no phone call required.