Monitoring Violations MO

Marshfield Public Water System

EPA ID: MO5010503 · 7,425 people served · 1 ZIP code

Five-year compliance data for Marshfield Public Water System includes 3 violations the EPA has not yet marked resolved — those open findings are part of the utility's current enforcement profile, covering a service population of approximately 7,425 residents across the area it supplies.

Data: EPA SDWIS Last verified: 2026-04-02

B · 70
Avg Safety Score
7,425
People Served
1
ZIP Code Served
13
Violations (5yr)
Groundwater
Water Source
0.00547 mg/L
Max Lead Level
Zone 2
Radon Risk · Moderate
6
Contaminants Flagged
$234K
Median Home Value in Service Area

Service Area Map

Coverage area for Marshfield Public Water System Source: EPA SDWIS service area boundaries.

Service area boundary — Grade B

Service Area Demographics

$76,304
Median Household Income
17,479
Service Area Population
88%
Disadvantaged Population
70th
Poverty Percentile
60th
Energy Burden Percentile
49%
Pre-1986 Housing

The Marshfield Public Water System serves a community with a median household income of $76,304 and an estimated 17,479 residents across its service area. Approximately 49% of housing stock was built before 1986, which increases the likelihood of lead service lines and older plumbing.

Environmental Justice Note: 88% of the population in this service area is classified as disadvantaged under EPA's EJScreen criteria. Communities with higher disadvantaged populations often face disproportionate environmental and health burdens, including aging water infrastructure and limited resources for remediation.

💧 Where Does Your Water Come From?

Groundwater

Marshfield Public Water System's water is pumped from underground aquifers. Groundwater is naturally filtered through rock and soil, but it can be vulnerable to PFAS contamination, nitrates from agriculture, and industrial chemicals that seep into the water table.

Moderate Risk
Source Contamination Risk
50th
Wastewater Discharge Proximity
40th
Superfund Site Proximity

About 4% of homes in Webster County, Missouri rely on private wells rather than public water systems. Private well owners are responsible for their own water testing and treatment.

Infrastructure Risk

43 yr
Avg Pipe Age
Copper
Pipe Material
27 yr
Est. Remaining Life
Moderate Wear
Decay Status
Installed 61% of expected lifespan used End of life

Detected Contaminants

How Marshfield Public Water System compares to EPA limits

What This Means For You

Contaminant 0700 at 6 mg/L exceeds the EPA maximum of mg/L.

Stage 1 DBP Rule at 2 mg/L exceeds the EPA maximum of mg/L.

Surface Water Treatment Rule at 2 mg/L exceeds the EPA maximum of mg/L.

Total Coliform at 1 presence exceeds the EPA maximum of presence.

Lead and Copper Rule at 1 mg/L exceeds the EPA maximum of mg/L.

Comparable Water Systems

Similar-sized systems in Missouri

C 1 violation
Adair County Pwsd 1
7,500 people
C 3 violations
Cole County Pwsd 4
7,568 people
0 violations
Pike County Pwsd 1
7,590 people
C 23 violations
Dekalb County Pwsd 1
7,635 people
C 12 violations

Estimated Remediation Costs

Average estimated costs across ZIP codes served by this system

Radon Mitigation
Radon Mitigation $400
Total Estimated Cost $400

Based on national averages for common remediation projects. Actual costs vary by property. Only issues flagged by EPA, FEMA, or state data for each ZIP code are included.

Cost of Inaction

If water quality issues in this service area are not addressed, the estimated financial impact per household is:

Estimated Healthcare Costs $1,000

Annual per household (CDC est.)

Estimated Cumulative Cost Per Household

5 years
$5,000
10 years
$10,000
20 years
$20,000

Compare: Estimated remediation cost is $400 (one-time) vs. $10,000 in estimated inaction costs over 10 years.

Estimates based on published EPA, CDC, and peer-reviewed research. Individual costs vary by household size, property, and health factors. These are conservative lower-bound estimates intended for awareness, not financial advice.

System Overview

Marshfield Public Water System (EPA ID: MO5010503) is a community water system in Missouri that serves approximately 7,425 people from groundwater sources.

This system serves ZIP code 65706 in Marshfield.

Average Home Safety Score: B (70/100)

Based on water quality violations, lead levels, and radon risk across all ZIP codes served by this system.

Violation History

13 monitoring/reporting violations recorded. These are procedural violations (missed tests or late reports), not necessarily water safety issues.

Recent Violations

Date Contaminant Type Status
September 24, 2025 Lead and Copper Rule Monitoring Resolved
July 1, 2025 Surface Water Treatment Rule Monitoring Unresolved
May 1, 2025 Contaminant 0700 Monitoring Resolved
February 1, 2025 Contaminant 0700 Monitoring Resolved
December 1, 2024 Consumer Confidence Report Rule Monitoring Resolved
October 1, 2024 Contaminant 0700 Monitoring Resolved
October 1, 2024 Stage 1 DBP Rule Monitoring Resolved
August 1, 2024 Contaminant 0700 Monitoring Resolved
May 1, 2024 Contaminant 0700 Monitoring Resolved
March 1, 2024 Contaminant 0700 Monitoring Unresolved
September 1, 2023 Total Coliform Monitoring Unresolved

Contaminants Detected

The following contaminants have been flagged in EPA records for this water system:

Contaminant Category Violations Health-Based
Contaminant 0700 Other Violation 6 No
Stage 1 DBP Rule Treatment Failure 2 No
Surface Water Treatment Rule Treatment Failure 2 No
Total Coliform Microbiological 1 No
Lead and Copper Rule Treatment Failure 1 No
Consumer Confidence Report Rule Reporting Failure 1 No

Lead & Copper

EPA Lead and Copper Rule sampling data for ZIP codes served by this system:

ZIP Code Lead Level Exceeds Limit Sample Date
65706 0.00547 mg/L No N/A

Radon Risk in Service Area

Dominant radon zone for ZIP codes served by this system: Zone 2 (Moderate Risk)

The EPA recommends testing homes in Zone 1 and Zone 2 areas for radon.

Need help with your water quality?

Typical cost: Water test: typically $20–$50 (DIY kit) · Professional inspection: $150–$400

Find the Right Water Filter

Free tip: Let cold water run for 2 minutes before drinking — this helps flush lead from your pipes.

ZIP Codes Served

Coverage: Service area ZIP codes sourced from EPA Community Water System Service Area Boundaries v3 (March 2026 release). These ZIPs reflect the actual deployment footprint recorded by MO or modeled from parcel and building-footprint data.

Data Sources

This report uses public data from the EPA Safe Drinking Water Information System (SDWIS). View the full compliance record for Marshfield Public Water System (MO5010503) on EPA.gov.

Frequently Asked Questions

Is Marshfield Public Water System water safe to drink?

Marshfield Public Water System has only monitoring/reporting violations, which are procedural in nature. The system meets federal health-based standards.

How many people does Marshfield Public Water System serve?

Marshfield Public Water System serves approximately 7,425 people across 1 ZIP code in Missouri.

Where does Marshfield Public Water System get its water?

The primary water source is groundwater.

Contact Your Water Utility

Public-record contact information for the water utility serving this system. Use these channels to request water quality reports, ask about service, or report issues directly.

Phone
417-468-2310
ZipCheckup is not affiliated with this water utility, does not act as its agent, and does not provide customer support for it. Contact details shown are public-record information from CCR filings. For service issues, contact the utility directly using the information above.

Contact information from MARSHFIELD PWS Consumer Confidence Report.

ZipCheckup is not affiliated with this water utility, does not act as its agent, and does not provide customer support for it. Contact details shown are public-record information from CCR filings. For service issues, contact the utility directly using the information above.

Water Source & Treatment

Where this water originates and how it's treated before reaching your tap.

Source
Groundwater
Drawn from underground aquifers via wells.
Treatment chemicals reported
fluoride

Source: MARSHFIELD PWS Consumer Confidence Report.

ZipCheckup is not affiliated with this water utility. Treatment and source data are sourced from the utility's published CCR filings.

Source water assessment from MARSHFIELD PWS Consumer Confidence Report:
The Department of Natural Resources conducted a source water assessment to determine the susceptibility of our water source to potential contaminants. Assessment maps and summary information sheets are available at https://drinkingwater.missouri.edu/.

Treatment regime

How this utility classifies its treatment process and what each reported treatment chemical does.

Treatment classification
Minimal — disinfection only
Disinfection (typically chlorine) without additional filtration or coagulation stages. Common for groundwater systems where source water meets federal standards after disinfection alone.

Treatment chemicals and what each one does

Chemical names are reported verbatim by the utility. Purpose categories are ZipCheckup annotations based on standard drinking-water treatment practice.

Fluoridation
Added at low levels per state or local public-health policy for dental health.
fluoride

Watershed exposure sources reported

Land-use and natural conditions identified in the utility's source-water assessment as potential contamination sources upstream of treatment.

Sewage treatment plantsSeptic systemsLivestock operationsUrban stormwater runoffIndustrial wastewaterOil and gas productionMiningFarming

Treatment classification and chemical list sourced from MARSHFIELD PWS Consumer Confidence Report.

Treatment intensity is a ZipCheckup-derived classification based on the chemicals and processes the utility reports. Chemicals and contamination sources are taken verbatim from the utility's CCR filing. Routine federal monitoring and contaminant testing shown elsewhere on this page determine whether the water meets safety standards, not the treatment classification.

Federal UCMR5 PFAS Monitoring: Tested Clean

This water system was tested under the federal EPA Unregulated Contaminant Monitoring Rule (UCMR5). No PFAS compounds were detected.

Samples collected
174

Current MCL reflects the lowest state-enforceable limit (NYS 10 ppt for PFOA/PFOS, effective August 2020). The federal final MCL of 4 ppt for PFOA/PFOS (EPA April 2024 rule) is not enforceable until April 2029. Detections above 4 ppt but below 10 ppt are below current MCL but above the future federal limit.

Source: U.S. EPA UCMR5 (Unregulated Contaminant Monitoring Rule, 5th cycle) — per-system federal sampling, 2023–2025. EPA UCMR5 monitoring program →

Understand PFAS health context and filtration →

Lead service line replacement plan from MARSHFIELD PWS Consumer Confidence Report:
<p>Lead service line inventory was required to be prepared and can be requested from MARSHFIELD PWS.</p><p>Special Lead and Copper Notice: Lead can cause serious health problems, especially for pregnant women and young children. MARSHFIELD PWS is responsible for providing high quality drinking water and removing water system owned and controlled lead pipes, but cannot control the variety of materials used in plumbing components in your home.</p>

Lead Service Line Replacement Tracker

This water utility's lead service line (LSL) replacement program is tracked from public Consumer Confidence Report filings. Email signup notifies subscribers when the utility files an updated replacement plan or progress milestone.

Get notified on replacement progress

Subscribers receive an email when this utility updates its LSL plan, files a milestone report, or adjusts replacement timelines. No marketing, no third-party sharing.

By submitting you agree to Privacy Policy. Unsubscribe anytime via the link in any email.

MARSHFIELD PWS

ZipCheckup is not affiliated with this water utility. LSL replacement-program data is sourced from public CCR filings published by the utility. Subscription notifications are based on automated parsing of subsequent CCR releases.

Learn more about Lead and Copper Rule replacement requirements →

Lead Service Line Inventory

Service line breakdown reported under the federal Lead and Copper Rule Improvements (LCRI) inventory requirement:

0
Confirmed Lead
0
Galvanized — Replacement Required
20
Unknown Material
3,185
Confirmed Non-Lead

This system reports zero confirmed lead service lines in its inventory. Unknown-material counts may still warrant verification.

Federal LCRI rule (effective October 2024) requires every public water system to inventory its service lines and complete lead-line replacement within 10 years.

Federal Regulatory Status · 2026Q1
LCRR inventory submission: Reported all required service line types
Latest tap sample on 2023-01-01 did not exceed the federal lead action level.
Population served: 7,425
Reported to Missouri

Source: EPA SDWIS Federal Service Line Inventory (Phase 2) · Submitted 2026

ZipCheckup is not affiliated with the utility or state agency. Inventory figures render verbatim from the public LCRI submission cited above; ZipCheckup does not perform inspections or replacements.

Learn about lead in drinking water →

Aesthetic water quality

These measurements describe the look, taste, and feel of the water this utility delivers. They are not contaminant violations — they sit alongside federal Secondary Maximum Contaminant Levels (SMCLs) which the EPA publishes as non-enforceable guidance.

pH
8.33
How acidic or basic the water is on a 0-14 scale. Drinking water is typically near neutral.
EPA secondary range: 6.5 – 8.5
Fluoride
0.11 ppm
Utility adds fluoride
Measured fluoride concentration in parts per million.
EPA secondary MCL: 2.0 ppm
Alkalinity
288 ppm CaCO₃
Capacity of the water to neutralize acids, expressed as calcium carbonate equivalent.
Total dissolved solids
344 ppm
Mineral content remaining after evaporation, including calcium, magnesium, sodium, and other dissolved substances.
EPA secondary MCL: 500 ppm

Aesthetic measurements from MARSHFIELD PWS Consumer Confidence Report.

Aesthetic measurements are reported by the utility from its annual sampling. EPA Secondary MCLs are advisory thresholds — values outside them indicate aesthetic concerns such as taste or appearance, not health violations. Federal contaminant testing is shown in the sections above.

Hard water detected in MARSHFIELD PWS

Your utility reported water hardness of 301 ppm CaCO₃ (17.6 grains per gallon) in its most recent Consumer Confidence Report. This is in the very hard range and may cause scale buildup, reduced appliance lifespan, and dry skin or hair.

Solutions for hard water

There are three common approaches to treating hard water: salt-based ion-exchange softeners (most effective, require salt refills), salt-free conditioners (lower maintenance, scale prevention only), and reverse osmosis at the kitchen sink (cooking and drinking water only). Aquasana, EcoWater, Pelican, and SpringWell are among the major US brands.

Recommended Aquasana system for your hardness level

Paid Partner. ZipCheckup earns commission on Aquasana purchases. We do not test water or verify product effectiveness for specific hardness levels — manufacturer claims are theirs alone. Consult a certified water-quality professional for personalized advice.

Hardness data parsed from this utility's most recent Consumer Confidence Report. Severity bands per USGS hard water classification.

Notable events and violations

This section summarizes events the utility chose to disclose in its most recent Consumer Confidence Report, plus any federal compliance violations the utility recorded against itself. Both lists are utility-authored — ZipCheckup does not audit, judge, or reorder them.

Federal compliance violations on record

These entries are taken verbatim from the utility's CCR violations section. EPA defines four broad violation categories: Maximum Contaminant Level (MCL), Treatment Technique (TT), Monitoring & Reporting (M&R), and Public Notification (PN).

  • public notice · LEAD AND COPPER RULE REVISIONS
    2025
    NOTIFICATION, KNOWN OR POTENTIAL LSL

Violations record from MARSHFIELD PWS Consumer Confidence Report.

Notable events from the utility's CCR

These bullet entries are the utility's own narration of operational, regulatory, or infrastructure events during the reporting period.

Notable events from MARSHFIELD PWS Consumer Confidence Report:
  • Uncorrected Significant Deficiencies identified: Water System Well Seal issue (05/29/2025)
  • Uncorrected Significant Deficiency: Known X Connection (05/29/2025)

ZipCheckup note: items above reflect what the utility published in its most recent CCR. Federal violation records are also tracked separately by the EPA Safe Drinking Water Information System (SDWIS) — the SDWIS record is the authoritative federal source for any specific regulatory action.

Frequently Asked Questions

Is water from Marshfield Public Water System safe to drink?
Marshfield Public Water System earns a B safety grade with 13 violations in the past 5 years. Tap water meets EPA standards for most contaminants.
What contaminants are in Marshfield Public Water System's water?
Detected contaminants include Contaminant 0700, Stage 1 DBP Rule, Surface Water Treatment Rule, Total Coliform. Each is compared against EPA maximum contaminant levels (MCLs) in the detailed breakdown above.
Should I use a water filter?
Given 5 contaminants above EPA limits, a certified water filter can provide an extra layer of protection. The best type depends on specific contaminants in your water.
How many people does Marshfield Public Water System serve?
Marshfield Public Water System serves approximately 7,425 people with drinking water across 1 ZIP code.
What is Marshfield Public Water System's water source?
Marshfield Public Water System draws water from groundwater sources. Source type affects which contaminants are most likely to be present.
Is there lead in Marshfield Public Water System's water?
The maximum detected lead level is 0.00547 mg/L. This is within EPA action level guidelines.
What is the demographic profile of Marshfield Public Water System's service area?
The Marshfield Public Water System service area has a median household income of $76,304. EPA EJScreen data classifies 88% of the population as disadvantaged, which may indicate greater vulnerability to environmental health risks.
Where does Marshfield Public Water System get its water?
Marshfield Public Water System's water is pumped from underground aquifers. Groundwater is naturally filtered through rock and soil, but it can be vulnerable to PFAS contamination, nitrates from agriculture, and industrial chemicals that seep into the water table. Based on available data, the source contamination risk is moderate.

What You Can Do

1

Test your water

Home test kits can detect lead, bacteria, and other contaminants at your tap. Find the right filter →

2

Check your specific ZIP code

Water quality can vary within a system. View nearest ZIP report →

3

Contact your utility

Marshfield Public Water System (EPA ID: MO5010503) — request the latest Consumer Confidence Report or ask about specific contaminants.

Home Water Systems Missouri Marshfield Public Water System

Get safety alerts for Marshfield Public Water System, Missouri

Free updates when EPA data changes for this area. No spam.

Unsubscribe anytime. Privacy Policy.

Share This Page

X Facebook
Violations found — check filter options Free tool — no phone call required.